- 您现在的位置：买卖IC网 > PDF目录1888 > 78P2351-IGTR/F (Maxim Integrated Products)LINE INTERFACE UNIT 100-LQFP PDF资料下载
参数资料
| 型号： | 78P2351-IGTR/F |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 24/42页 |
| 文件大小： | 0K |
| 描述： | LINE INTERFACE UNIT 100-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 1/1 |
| 规程： | E4，OC-3，STM1-E |
| 电源电压： | 3.15 V ~ 3.45 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-LQFP（16x16） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
78P2351
Single Channel
OC-3/ STM1-E/ E4 LIU
Page: 30 of 42
2006 Teridian Semiconductor Corporation
Rev. 2.4
ELECTRICAL SPECIFICATIONS (continued)
(Note 1)
0.60
0.55
0.50
0.45
0.40
0.05
-0.05
-0.50
-0.55
-0.60
-0.45
-0.40
(Note 1)
0.35ns
Nominal
Zero Level
(Note 2)
T = 7.18ns
0.1ns
1ns
1.795 ns
1ns
0.1ns
1ns
Nominal
Pulse
0.35ns
V
Note 1 – The maximum “steady state” amplitude should not exceed the 0.55V limit. Overshoots and other transients are permitted to fall into
the shaded area bounded by the amplitude levels 0.55V and 0.6V, provided that they do not exceed the steady state level by more than
0.05V.
Note 2 – For all measurements using these masks, the signal should be AC coupled, using a capacitor of not less than 0.01
F, to the input of
the oscilloscope used for measurements. The nominal zero level for both masks should be aligned with the oscilloscope trace with no input
signal. With the signal then applied, the vertical position of the trace can be adjusted with the objective of meeting the limits of the masks. Any
such adjustment should be the same for both masks and should not exceed
±0.05V. This may be checked by removing the input signal again
and verifying that the trace lies with
±0.05V of the nominal zero level of the masks.
Note 3 – Each pulse in a coded pulse sequence should meet the limits of the relevant mask, irrespective of the state of the preceding or
succeeding pulses, with both pulse masks fixed in the same relation to a common timing reference, i.e. with their nominal start and finish
edges coincident. The masks allow for HF jitter caused by intersymbol interference in the output stage, but not for jitter present in the timing
signal associated with the source of the interface signal. When using an oscilloscope technique to determine pulse compliance with the mask,
it is important that successive traces of the pulses overlay in order to suppress the effects of low frequency jitter. This can be accomplished by
several techniques [e.g. a) triggering the oscilloscope on the measured waveform or b) providing both the oscilloscope and the pulse output
circuits with the same clock signal].
Note 4 – For the purpose of these masks, the rise time and decay time should be measured between –0.4V and 0.4V, and should not exceed
2ns.
Figure 12 – Mask of a Pulse corresponding to a binary Zero in E4 mode
相关PDF资料 |
PDF描述 |
|---|---|
| 78P2351R-IMR/F | IC LIU NRZ-CMI CONV 155M 56-QFN |
| 78P2352-IELR/F | IC LIU SDH SONET 2CH 128-LQFP |
| 78Q2120C09-64CGTR/F | TXRX 10/100 BASE 3.3V 64-LQFP |
| 78Q2133/F | TXRX 10/100 MDIX 3.3V IND 32-QFN |
| 78Q8392LA03-28CHR/F | TXRX 10BASE 2/5 ETH COAX 28-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 78P2351R | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Serial 155M NRZ to CMI Converter |
| 78P2351R-DB | 功能描述:界面开发工具 78P2351R Demo Brd RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| 78P2351R-IM | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Serial 155M NRZ to CMI Converter |
| 78P2351R-IM/F | 功能描述:接口 - 专用 Serial 155M NRZ to CMI Converter RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| 78P2351R-IMR | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Serial 155M NRZ to CMI Converter |
发布紧急采购，3分钟左右您将得到回复。