- 您现在的位置：买卖IC网 > Datasheet目录611 > 90276-2 (TE Connectivity)HHHT PIDG PG FASTON 10-12 Datasheet资料下载
参数资料
| 型号： | 90276-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | HHHT PIDG PG FASTON 10-12 |
| 标准包装： | 5 |
| 系列： | Certi-Crimp™, PIDG™, Faston™ |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 快速连接端子，10-12 AWG |
| 特点： | 侧面插入，棘齿 |
Refer to Figure 2 and select a wire of the specified
size and insulation diameter. Strip the wire to the
length indicated. Do not cut or nick the wire strands.
Select an applicable loose–piece terminal. Refer to
Figure 3 and proceed as follows:
1. Hold the tool so that the front (terminal side) is
facing you.
2. Make sure that the ratchet is released. Squeeze
the tool handles together and allow them to open
fully.
3. Insert terminal (mating portion first) straight into
front of crimp section. Push terminal mating portion
into locator slot until wire barrel butts against
locator.
4. Holding terminal in place, squeeze tool handles
together until crimping dies close just enough to
retain terminal. Do not deform insulation barrel or
wire barrel.
5. Insert a properly stripped wire into terminal wire
barrel until wire butts against locator.
6. While holding the wire in place, squeeze the tool
handles together until the ratchet releases.
7. Allow the tool handles to open fully. Remove the
crimped terminal from the tool.
The insulation barrel crimp height is regulated by
placing the insulation adjustment pin in one of three
positions: (1) small, (2) medium, or (3) large.
Determine the proper setting as follows:
1. Place adjustment pin in No. 3 position. Insert
terminal into tool according to Section 3,
CRIMPING PROCEDURE, Steps 1 through 4.
2. Insert an unstripped wire into terminal insulation
barrel. Crimp terminal and remove from tool.
3. Check insulation crimp by bending wire back
and forth one time. If wire pulls out, place
adjustment pin in next smaller position and repeat
these procedures. Crimp should hold wire
insulation firmly without cutting into it.
Remove all foreign particles with a clean, soft brush
or a clean, soft, lint–free cloth. Make sure the proper
retaining pins are in place and are secured with the
proper retaining rings. If foreign matter cannot be
removed easily, or if the proper replacement parts are
not available, return the tool to your supervisor.
Make sure all pivot points and bearing surfaces are
protected with a thin coat of any good SAE 20 motor
oil. Do NOT oil excessively. When the tool is not in
use, keep the handles closed to prevent objects from
becoming lodged between the dies, and store the tool
in a clean, dry area.
Figure 3
相关PDF资料 |
PDF描述 |
|---|---|
| 90280-1 | DIE PIDG 12-10 |
| 90294-1 | SAHT F CRIMP 22-26 |
| 90308-1 | SAHT LKG CLIP 031X.062 |
| 90313-2 | SAHT |
| 90327-1 | SAHT TYPE VI |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 902-765 | 功能描述:支架与垫片 Plastic Spcr .765 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 902767-000 | 制造商:TE Connectivity 功能描述:D-SCE-25-50-S1-4 - Bulk |
| 90277 | 制造商:ESSEX 功能描述:ESSEX |
| 902-770 | 功能描述:支架与垫片 Plastic Spcr .77 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 902-77-02113 | 制造商:TE Connectivity 功能描述:SCREW,SHOULDER,10 |
发布紧急采购，3分钟左右您将得到回复。