- 您现在的位置：买卖IC网 > Datasheet目录611 > 90276-2 (TE Connectivity)HHHT PIDG PG FASTON 10-12 Datasheet资料下载
参数资料
| 型号： | 90276-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | HHHT PIDG PG FASTON 10-12 |
| 标准包装： | 5 |
| 系列： | Certi-Crimp™, PIDG™, Faston™ |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 快速连接端子，10-12 AWG |
| 特点： | 侧面插入，棘齿 |
Figure 4
Tyco Electronics does not manufacture or market
Regular inspection should be performed by quality
control personnel. A record of scheduled inspections
should remain with the tool and/or be supplied to the
supervisory personnel responsible for the tool.
Though recommendations call for at least one
inspection a month, the inspection frequency should
be based on the amount of use, ambient working
conditions, operator training and skill, and established
company standards. These inspections should be
performed in the following sequence:
1. Remove all lubrication and accumulated film by
immersing the tool (handles partially closed) into a
suitable degreaser that will not affect paint or
plastic material.
2. Make certain all retaining pins are in place and
are secured with the proper retaining rings. If
replacements are necessary, refer to Figure 5.
3. Close the tool handles until the ratchet releases,
and then allow the handles to open freely. If they
do not open quickly and fully, then the spring is
defective and must be replaced (see Section 6,
REPLACEMENT AND REPAIR).
4. Inspect the tool, with special emphasis on
checking for worn, cracked, or broken crimping
dies. If damage to any part of the head is evident,
these gages. To gage the crimping chamber, proceed
as follows:
1. Remove traces of oil or dirt from the crimping
chamber and plug gages.
2. Close the tool handles until it is evident that the
jaws have bottomed; then hold in this position. Do
NOT force the jaws beyond initial contact.
3. Align the GO element with the appropriate
section of the crimping chamber. Push element
straight into the crimping chamber without using
force. The GO element must pass completely
through the crimping chamber as shown in
Figure 4.
4. Align the NO–GO element and try to insert it
straight into the same section of the crimping
chamber. The NO–GO element may start entry,
but must not pass completely through the crimping
chamber. See Figure 4.
If the crimping chamber conforms to the gage
inspection, the crimping chamber is considered
dimensionally correct, and should be lubricated with a
THIN coat of any good SAE 20 motor oil. If not, the
tool must be returned to Tyco Electronics for further
evaluation and repair. Refer to Section 6,
REPLACEMENT AND REPAIR.
For additional information regarding the use of plug
gages, refer to Instruction Sheet 408–7424.
return the tool for evaluation and repair (see
Section 6, REPLACEMENT AND REPAIR).
Obtain a 0.025 mm [.001 in.] shim that is suitable for
This inspection requires the use of plug gages
conforming to the dimensions provided in Figure 4.
checking the clearance between the bottoming
surfaces of the crimping dies. Proceed as follows:
相关PDF资料 |
PDF描述 |
|---|---|
| 90280-1 | DIE PIDG 12-10 |
| 90294-1 | SAHT F CRIMP 22-26 |
| 90308-1 | SAHT LKG CLIP 031X.062 |
| 90313-2 | SAHT |
| 90327-1 | SAHT TYPE VI |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 902-765 | 功能描述:支架与垫片 Plastic Spcr .765 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 902767-000 | 制造商:TE Connectivity 功能描述:D-SCE-25-50-S1-4 - Bulk |
| 90277 | 制造商:ESSEX 功能描述:ESSEX |
| 902-770 | 功能描述:支架与垫片 Plastic Spcr .77 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 902-77-02113 | 制造商:TE Connectivity 功能描述:SCREW,SHOULDER,10 |
发布紧急采购，3分钟左右您将得到回复。