- 您现在的位置：买卖IC网 > Datasheet目录612 > 90800-2 (TE Connectivity)DIE SET HI-DEN D-SUB CRIMP CONT Datasheet资料下载
参数资料
| 型号： | 90800-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | DIE SET HI-DEN D-SUB CRIMP CONT |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 压接或电缆尺寸： | 22-28 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 压接端子 |
| 配用： | 1658670-5-ND - CONN PIN 22-28AWG CRIMP 30GOLD A31956-ND - CONN D-SUB SOCKET 22-28AWG GOLD A31955-ND - CONN D-SUB SOCKET 22-28AWG GOLD A31954-ND - CONN D-SUB PIN 22-28AWG GOLD A31953-ND - CONN D-SUB PIN 22-28AWG GOLD |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A9816 |
408-4007
Nut
Locator
Locator Assembly
Tool Jaws
Chamfer
Offset
Wire Crimper
Die
Die Retaining Pin
(4 Places)
Long Die Retaining
Screw
Wire Anvil
Die
Insulation
Crimper
Die
Chamfer
Insulation Anvil
Die
Short Die Retaining
Screw
Figure 2
The tool frame is provided with a crimp adjustment
feature. Initially, the crimp height should be verified
i
When closed, the dies form two crimping chambers.
Each die is held in the tool frame by a retaining screw
and two retaining pins.
3. INSTALLATION AND REMOVAL OF DIE ASSEMBLY
AND LOCATOR ASSEMBLY
1. Close the tool handles until the ratchet releases,
then allow the handles to open fully.
2. Remove the two die retaining screws from the
tool jaws.
3. Slide the wire anvil and insulation anvil dies onto
the moving jaw so that the chamfers and marked
surfaces face outward as shown in Figure 2, then
insert the two die retaining pins through the holes in
the moving jaw and into the holes in the dies.
4. Thread, but do not tighten, the short die retaining
screws through the holes of the moving jaw and into
the holes in both anvil dies.
5. Slide the wire crimper and insulation crimper dies
onto the stationary jaw so that the chamfers and
marked surfaces face outward as shown in Figure 2,
then insert the two die retaining pins through the holes
in the stationary jaw and into the holes in the dies.
6. Thread, but do not tighten, the long die retaining
screws through the holes of the moving jaw and into
the holes in both crimper dies.
7. Carefully close the tool handles, making sure that
the dies align properly. Continue closing the
handles until the ratchet has engaged sufficiently to
hold the dies in place.
8. Tighten the die retaining screws using the
appropriate screwdriver.
Rev D
9. Place the locator assembly over the end of the
long die retaining screw, and position the locator
assembly against the side of the tool jaw.
10. Place the nut onto the end of the long die
retaining screw, and tighten the nut enough to hold
the locator assembly in place, while still allowing the
locator to slide up and down.
11. To disassemble, close the tool handles until the
ratchet releases. Remove the nut, locator assembly,
the two die retaining screws, and four die retaining
pins, then, slide the dies out of the tool jaws.
4. CRIMPING PROCEDURE
NOTE
according to Section 6, CRIMP HEIGHT
INSPECTION, and if necessary, adjusted
according to Section 7, CRIMP HEIGHT
ADJUSTMENT before using the tool.
Refer to Figure 1, and select wire of the specified size
and insulation diameter. Strip the wire to the
dimension given in Figure 1, taking care not to nick or
cut wire strands. Then proceed as follows:
1. Hold the tool so that the back (wire side) faces
you. Close the tool handles until the ratchet
releases, then allow the handles to open FULLY.
2. Insert the contact (insulation barrel first) into the
front of the appropriate crimping chamber (refer to
the markings on the die).
3. Position the contact so that the mating end is on
the locator side of the tool frame and the open “U” of
the wire barrel and insulation barrel faces the top of
2 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 90869-2 | DIE SET 24-18 AWG USE WITH A9996 |
| 90870-2 | DIE SET FOR PROC III 30-28,26-24 |
| 90871-2 | DIE SET 20-14 AWG USE WITH A9996 |
| 90872-1 | TOOL CRIMP .093 AWG 24 W/DIE |
| 91002-1 | TOOL INSERTION .062 & .093 CONN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 908-0020 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:PUNCH 15 WAY D FRONT MOUNT |
| 908-0030 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:PUNCH 25 WAY D FRONT MOUNT |
| 908003004 | 制造商:Molex 功能描述: |
| 90800-3004 | 功能描述:集管和线壳 1.27mm PF Hdr RA Lop opro Stag.76Au 4 Ckt RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 90800-3006 | 功能描述:集管和线壳 1.27MM PF HDR RA LOP OPRO STAG.76AU 6 CKT RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
发布紧急采购，3分钟左右您将得到回复。