- 您现在的位置：买卖IC网 > Datasheet目录612 > 90800-2 (TE Connectivity)DIE SET HI-DEN D-SUB CRIMP CONT Datasheet资料下载
参数资料
| 型号： | 90800-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | DIE SET HI-DEN D-SUB CRIMP CONT |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 压接或电缆尺寸： | 22-28 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 压接端子 |
| 配用： | 1658670-5-ND - CONN PIN 22-28AWG CRIMP 30GOLD A31956-ND - CONN D-SUB SOCKET 22-28AWG GOLD A31955-ND - CONN D-SUB SOCKET 22-28AWG GOLD A31954-ND - CONN D-SUB PIN 22-28AWG GOLD A31953-ND - CONN D-SUB PIN 22-28AWG GOLD |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A9816 |
408-4007
Contact Support
Adjustment
Screw for
Contact Support
Back of
Tool Frame
(Wire Side)
Wire
Figure 3
Locator in
Wire Stop Slot
of Contact
Crimping
Chamber
Wire Strip Length
Wire Inserted
to Wire Stop
Make sure that both sides of the insulation barrel
!
The ratchet has detents that create audible clicks
as the tool handles are closed.
The crimped contact may stick in the crimping area;
however the contact can be removed by pushing
i
the tool frame. Place the contact up into the
crimping chamber so that the locator drops into the
slot in the contact. Refer to Figure 3. Butt the front
end of the wire barrel against the locator.
CAUTION
are started evenly into the crimping chamber.
DO NOT attempt to crimp an improperly positioned
contact.
4. Hold the contact in position, and close the tool
handles until the ratchet engages sufficiently to hold
the contact in position. DO NOT deform the
insulation barrel or wire barrel.
5. Insert the stripped wire into contact insulation
barrel and wire barrel until it is butted against the
wire stop as shown in Figure 3.
6. Holding the wire in place, close the tool handles
until the ratchet releases.
7. Allow the tool handles to open FULLY, and
remove the crimped contact.
NOTE
downward on the top of the locator (see Figure 3).
8. Check the contact crimp height, and if necessary,
adjust the crimp height
Proceed as follows:
1. Make a sample crimp and determine if the
contact is bending (upward or downward).
2. Loosen the screw that holds the contact support
onto the locator assembly.
3. Place a contact with a wire into the proper
crimping chamber, and close the tool handles until
the ratchet reaches the sixth click or until the
contact support touches the contact.
NOTE
i
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
5. Move the contact support as required to eliminate
the bending of the contact.
6. Tighten the nut, then close the handles until the
ratchet releases.
7. Remove and inspect the contact. Make another
sample crimp. If the contact is straight, tighten the
contact support screw. If the contact is still being
bent during crimping, repeat the adjustment
procedure.
CAUTION
DO NOT use defective or damaged products.
5.2. Ratchet Adjustment
!
5. ADJUSTMENTS
5.1. Contact Support
The contact support is preset prior to shipment, but
minor adjustment may be necessary if the contact is
bending during crimping.
Rev D
The tool ratchet mechanism features an adjustment
wheel with numbered settings. The adjustment wheel
controls the amount of handle pressure exerted on the
jaws during crimping. If the crimp is not acceptable,
adjust the ratchet as follows:
1. Remove the lockscrew from the ratchet
adjustment wheel. Refer to Figure 4.
2. Using a screwdriver, adjust the ratchet wheel
from the front of the tool.
3 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 90869-2 | DIE SET 24-18 AWG USE WITH A9996 |
| 90870-2 | DIE SET FOR PROC III 30-28,26-24 |
| 90871-2 | DIE SET 20-14 AWG USE WITH A9996 |
| 90872-1 | TOOL CRIMP .093 AWG 24 W/DIE |
| 91002-1 | TOOL INSERTION .062 & .093 CONN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 908-0020 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:PUNCH 15 WAY D FRONT MOUNT |
| 908-0030 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:PUNCH 25 WAY D FRONT MOUNT |
| 908003004 | 制造商:Molex 功能描述: |
| 90800-3004 | 功能描述:集管和线壳 1.27mm PF Hdr RA Lop opro Stag.76Au 4 Ckt RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 90800-3006 | 功能描述:集管和线壳 1.27MM PF HDR RA LOP OPRO STAG.76AU 6 CKT RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
发布紧急采购，3分钟左右您将得到回复。