- 您现在的位置：买卖IC网 > Datasheet目录613 > 91338-1 (TE Connectivity)0.64 MM CONTACT PRO-CRIMPER Datasheet资料下载
参数资料
| 型号： | 91338-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/6页 |
| 文件大小： | 0K |
| 描述： | 0.64 MM CONTACT PRO-CRIMPER |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 触点，18-20 AWG |
| 特点： | 侧面插入，棘齿 |
PRO- CRIMPER III Hand Crimping Tool Assembly 91338- 1
408- 8377
Nuts
(2)
Chamfered
Edge (Typ)
Wire Crimper
Wire Anvil
Contact
Support
Locator Assembly
Contact Locator
Insulation
Crimper
Tool Frame
Short
Die Retaining
Pins (2)
Long Die Retaining
Screw
Markings Face
Outward (Typ)
Chamfered
Edge (Typ)
Insulation
Anvil
Short Die Retaining
Screw
Long
Die Retaining
Pins (2)
Figure 2
Attached to the outside of the jaw is a contact
support. A nut is used on the lower die retaining
screw to hold the contact support in place.
3. INSTALLATION AND REMOVAL OF DIE ASSEMBLY,
LOCATOR ASSEMBLY, AND CONTACT SUPPORT
1. Open the tool handles, and remove the two die
retaining screws from the tool jaws. See Figure 2.
2. Place the wire anvil and insulation anvil so that
the chamfered sides and marked surfaces face
outward, when mounted in the moving jaw of the
tool frame.
3. Insert two long die retaining pins through the
tool frame and the anvils.
4. Insert the short die retaining screw through the
jaw and through both anvil dies. Tighten the screw
just enough to hold the dies in place. Do not
tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper so
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
6. Insert two short die retaining pins through the
tool frame and into the crimpers.
7. Insert the long die retaining screw through the
jaw and through both crimper dies. Tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
8. Carefully close the tool handles, making sure
that the anvils and crimpers align properly.
Continue closing the tool handles until the ratchet
in the tool frame has engaged sufficiently to hold
the anvils and crimpers in place, then tighten both
die retaining screws.
9. Place the locator assembly over the end of the
long die retaining screw. Position the locator
assembly against the side of the tool jaw.
10. Place a nut onto the end of the long screw and
tighten the nut enough to hold the locator assembly
in place, while still allowing the contact locator to
slide up and down.
11. Place the contact support, with the chamfered
side out, over the end of the short screw and long
pins. Secure with a nut.
12. To disassemble, close the tool handles until the
ratchet releases, remove the two nuts, the locator
assembly, the contact support, the two die
retaining screws, and the four die retaining pins.
Slide the anvils and crimpers out of the tool jaws.
2 of 6
Tyco Electronics Corporation
Rev A
相关PDF资料 |
PDF描述 |
|---|---|
| 91338-2 | TOOL HAND PRO CRIMPER 20-18AWG |
| 91346-1 | 2MM HM SEATING TOOL TYPE AB 25 |
| 91349-4 | SEATING TL HDR 4 PR 20 COL |
| 91360-1 | SEATING TL 2MM HM TYPE M |
| 91369-2 | PRO-C DIE SL156 16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 91338-1003 | 制造商:MOLEX 制造商全称:Molex Electronics Ltd. 功能描述:5.00mm (.197") Pitch Appli-Mate RAST 5 Female Connector, Vertical, 1 Circuit, Grey, Tin (Sn) Plating |
| 91338-1004 | 制造商:MOLEX 制造商全称:Molex Electronics Ltd. 功能描述:5.00mm (.197") Pitch Appli-Mate RAST 5 Female Connector, Vertical, 1 Circuit, Yellow, Tin (Sn) Plating |
| 91338-2 | 功能描述:冲压机与冲模 PRO CRIMPER DIE .64MM RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 913382-000 | 制造商:ELO Touch Solutions 功能描述:PANEL;17.0IN;FLAT PROFILE;ANTI |
| 91338-3403 | 制造商:MOLEX 制造商全称:Molex Electronics Ltd. 功能描述:5.00mm (.197") Pitch Appli-Mate RAST 5 Female Connector, Vertical, 1 Circuit, Blue, Silver (Ag) Plating, Reference K03 |
发布紧急采购，3分钟左右您将得到回复。