- 您现在的位置：买卖IC网 > Datasheet目录613 > 91338-1 (TE Connectivity)0.64 MM CONTACT PRO-CRIMPER Datasheet资料下载
参数资料
| 型号： | 91338-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | 0.64 MM CONTACT PRO-CRIMPER |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 触点，18-20 AWG |
| 特点： | 侧面插入，棘齿 |
The contact locator is preset prior to shipment,
but a minor adjustment may be necessary.
i
PRO- CRIMPER III Hand Crimping Tool Assembly 91338- 1
4. CONTACT LOCATOR ADJUSTMENT
NOTE
i
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
2. If adjustment is required, loosen the screw that
holds the contact locator onto the locator
assembly.
NOTE The ratchet has detents that create audible clicks
as the tool handles are closed.
i
3. Place a contact with wire into the proper crimp
section and close the tool handles until the ratchet
reaches the sixth click, or until the contact locator
touches the contact.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
5. Move the contact locator as required to
eliminate the bending of the contact.
6. Tighten the nut and close the handles until the
ratchet releases.
7. Remove and inspect the contact.
8. Make another sample crimp. If the contact is
straight, tighten the contact locator screw. If the
408- 8377
contact is still being bent during crimping, repeat
the adjustment procedure.
5. CRIMPING PROCEDURE
NOTE This tool is provided with a crimp adjustment
feature. Initially, the crimp height should be
verified as specified in Section 6, CRIMP
HEIGHT INSPECTION, and Section 7,
RATCHET (Crimp Height) ADJUSTMENT, before
using the tool to crimp desired contacts.
Refer to Figure 1, and select wire of the specified size
and insulation diameter. Strip the wire to the length
indicated, taking care not to nick or cut wire strands.
Select an applicable contact and identify the
appropriate crimping chamber according to the wire
size markings on the tool.
Refer to Figure 3, and proceed as follows:
1. Hold the tool so that the back (wire side) is
facing you. Squeeze tool handles together and
allow them to open fully.
2. Holding the contact by the mating end, insert the
contact -- insulation barrel first -- through the front
of the tool and into the appropriate crimp section.
3. Place the contact into the contact support and
position the contact so that the mating end is on
the locator side of the tool. Make sure that the
open “U” of the wire barrel and insulation barrel
face the stationary jaw.
4. Carefully close the tool, positioning the contact
so that the movable locator enters the contact wire
stop slot between the wire barrel and contact
shoulder. Butt the wire barrel against the locator.
Adjustment
Screw for
Contact
Locator
Locator
Back of Tool
(Wire Side)
Wire
Contact
Mating
End
Tool Stationary Jaw
Wire Strip Length
Contact
Support
Contact
Support
Locator in Contact
Wire Stop Slot
Figure 3
Wire Inserted to
Locator Wire Stop
Rev A
Tyco Electronics Corporation
3 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 91338-2 | TOOL HAND PRO CRIMPER 20-18AWG |
| 91346-1 | 2MM HM SEATING TOOL TYPE AB 25 |
| 91349-4 | SEATING TL HDR 4 PR 20 COL |
| 91360-1 | SEATING TL 2MM HM TYPE M |
| 91369-2 | PRO-C DIE SL156 16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 91338-1003 | 制造商:MOLEX 制造商全称:Molex Electronics Ltd. 功能描述:5.00mm (.197") Pitch Appli-Mate RAST 5 Female Connector, Vertical, 1 Circuit, Grey, Tin (Sn) Plating |
| 91338-1004 | 制造商:MOLEX 制造商全称:Molex Electronics Ltd. 功能描述:5.00mm (.197") Pitch Appli-Mate RAST 5 Female Connector, Vertical, 1 Circuit, Yellow, Tin (Sn) Plating |
| 91338-2 | 功能描述:冲压机与冲模 PRO CRIMPER DIE .64MM RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 913382-000 | 制造商:ELO Touch Solutions 功能描述:PANEL;17.0IN;FLAT PROFILE;ANTI |
| 91338-3403 | 制造商:MOLEX 制造商全称:Molex Electronics Ltd. 功能描述:5.00mm (.197") Pitch Appli-Mate RAST 5 Female Connector, Vertical, 1 Circuit, Blue, Silver (Ag) Plating, Reference K03 |
发布紧急采购，3分钟左右您将得到回复。