- 您现在的位置：买卖IC网 > PDF目录18525 > 91902-1 (TE Connectivity)TOOL DIE ASSEM USE W/A9996-ND PDF资料下载
参数资料
| 型号： | 91902-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 1/4页 |
| 文件大小： | 0K |
| 描述： | TOOL DIE ASSEM USE W/A9996-ND |
| 标准包装： | 25 |
| 系列： | Coaxicon |
| 压接或电缆尺寸： | RG/U-142，142A，142B |
| 压接手柄： | A9996-ND |
| 连接器类型： | 压接端子 |
| 相关产品： | A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A29142 |
Each four–piece die assembly consists of two
indenter dies and two anvil dies. When closed, the die
assembly forms two or three crimping chambers. The
larger crimping chambers crimp the ferrule of the
connector onto the coaxial cable, and the smaller
crimping chamber crimps the center contact onto the
center conductor of the coaxial cable. Each set of
dies is held in the tool frame by two pins and a screw.
1. Close the tool handles until the ratchet releases,
then allow the tool handles to open fully.
2. Remove the two die retaining screws and four
die retaining pins from the tool jaws.
3. Install the anvil dies in the movable jaw of the
tool frame so that the chamfered edges and
marked surfaces face outward. Align the dies with
the screw hole, then insert the two die retaining
pins included with the die assembly through the
holes in the dies and into the holes in the tool
frame.
4. Secure the anvil dies with the die retaining
screw included with the die assembly. DO NOT
fully tighten the screw.
Figure 1
The SDE crimping die assemblies listed in Figure 1
are designed to crimp the products also listed in
Figure 1. The die assembly must be installed into
PRO–CRIMPER* III Frame Assembly 354940–1.
Refer to instruction sheet 408–9930 for information on
the hand tool frame.
Reasons for reissue of this instruction sheet are
provided in Section 8, REVISION SUMMARY.
5. Install indenter dies in the stationary jaw of the
tool frame so that the chamfered edges and
marked surfaces face outward. Align the dies with
the screw hole, then insert the two die retaining
pins included with the die assembly through the
holes in the dies and into the holes in the tool
frame.
6. Secure the indenter dies with the die retaining
screw included with the die assembly. DO NOT
fully tighten the screw.
7. Slowly close the tool handles, making sure that
the dies align properly. After the anvil dies enter
the indenter dies, place a 1.57+0.05–mm
[.062+.002–in.] diameter copper bus bar into the
center contact crimping chamber of the die
assembly.
8. Continue closing the tool handles until the
ratchet has engaged sufficiently to hold the dies in
place, then tighten both die retaining screws.
相关PDF资料 |
PDF描述 |
|---|---|
| ATS060B | CRYSTAL 6.0 MHZ 18PF |
| ASA2-16.000MHZ-L-T | OSC 16.000 MHZ 1.8V SMD |
| 252A154A40NB | POT JOYSTICK 150K OHM W/SWITCH |
| ATS12A | CRYSTAL 12 MHZ 20 PF FUND |
| 252B124A40NB | POT JOYSTICK 120K OHM W/SWITCH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9190292 | 制造商:Glenair Inc 功能描述:COVER - Bulk |
| 9190293 | 制造商:Amphenol Corporation 功能描述:10-189231-032 - Bulk |
| 91-903 | 制造商:Stancor 功能描述:Electromechanical Relay DPDT 15A 208/240VAC |
| 9190-3 | 功能描述:螺丝和紧固件 BIND HEAD SCRW BLACK RoHS:否 制造商:Unspecified 产品: 类型:Washer 螺纹大小: 长度: 材料:Steel 电镀:Nickel 螺丝头: 螺丝类型: |
| 9-1903015-3 | 功能描述:HDMI, Displayport和DVI连接器 HDMI REC SMT WITH TAPE RoHS:否 制造商:Molex 系列:DisplayPort 产品类型:Displayport 型式:Female 位置/触点数量:20 端接类型:Solder 安装风格:SMD/SMT 方向:Right Angle 触点电镀:Gold |
发布紧急采购，3分钟左右您将得到回复。