- 您现在的位置：买卖IC网 > PDF目录18525 > 91902-1 (TE Connectivity)TOOL DIE ASSEM USE W/A9996-ND PDF资料下载
参数资料
| 型号： | 91902-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | TOOL DIE ASSEM USE W/A9996-ND |
| 标准包装： | 25 |
| 系列： | Coaxicon |
| 压接或电缆尺寸： | RG/U-142，142A，142B |
| 压接手柄： | A9996-ND |
| 连接器类型： | 压接端子 |
| 相关产品： | A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A29142 |
4. Make a sample crimp and measure the crimp
height. If the crimp height is still unacceptable,
remove lockscrew and continue to adjust the
ratchet.
The die assembly is inspected before shipment. It is
recommended that the die assembly be inspected
immediately upon arrival at your facility to ensure that
the dies have not been damaged during shipment.
The die assembly will perform correctly as long as:
(1) the product specified is correct for the application,
(2) the proper die assembly is used, (3) the die
assembly has been measured to ensure that the
openings are correct, and (4) the tool has been
adjusted correctly.
Figure 3
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or a clean, soft, lint–free
cloth. DO NOT use any objects that could damage
The tool frame ratchet mechanism features an
adjustment wheel with numbered settings. If the crimp
height is not acceptable, adjust the ratchet as follows:
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. Using a screwdriver, rotate the ratchet
adjustment wheel from the opposite side of the tool
frame. If a tighter crimp is required, rotate the
ratchet adjustment wheel counterclockwise to a
higher–numbered setting. If a looser crimp is
required, rotate the ratchet adjustment wheel
clockwise to a lower–numbered setting.
3. Re–install the lockscrew.
Figure 4
the dies or tool.
2. Make sure that the proper die retaining screws
are properly secured.
3. When the dies are not in use, store them in a
clean, dry area.
1. Remove all lubrication and accumulated film
from the dies by immersing the dies in a suitable
commercial degreaser.
2. Make certain that die retaining screws and pins
are properly secured.
3. Inspect the crimping surfaces for flattened,
chipped, worn, or cracked areas. If damage is
evident, the dies must be replaced. Refer to
Section 7, REPLACEMENT.
4. Measure the die opening to ensure that it meets
the dimensions given in Figure 5.
Order replacements through your local
representative, or call 1–800–526–5142, or send a
facsimile of your purchase order to 1–717–986–7605,
or write to:
CUSTOMER SERVICE (038–035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105–3608
相关PDF资料 |
PDF描述 |
|---|---|
| ATS060B | CRYSTAL 6.0 MHZ 18PF |
| ASA2-16.000MHZ-L-T | OSC 16.000 MHZ 1.8V SMD |
| 252A154A40NB | POT JOYSTICK 150K OHM W/SWITCH |
| ATS12A | CRYSTAL 12 MHZ 20 PF FUND |
| 252B124A40NB | POT JOYSTICK 120K OHM W/SWITCH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9190292 | 制造商:Glenair Inc 功能描述:COVER - Bulk |
| 9190293 | 制造商:Amphenol Corporation 功能描述:10-189231-032 - Bulk |
| 91-903 | 制造商:Stancor 功能描述:Electromechanical Relay DPDT 15A 208/240VAC |
| 9190-3 | 功能描述:螺丝和紧固件 BIND HEAD SCRW BLACK RoHS:否 制造商:Unspecified 产品: 类型:Washer 螺纹大小: 长度: 材料:Steel 电镀:Nickel 螺丝头: 螺丝类型: |
| 9-1903015-3 | 功能描述:HDMI, Displayport和DVI连接器 HDMI REC SMT WITH TAPE RoHS:否 制造商:Molex 系列:DisplayPort 产品类型:Displayport 型式:Female 位置/触点数量:20 端接类型:Solder 安装风格:SMD/SMT 方向:Right Angle 触点电镀:Gold |
发布紧急采购，3分钟左右您将得到回复。