- 您现在的位置：买卖IC网 > PDF目录24864 > 950908BGLF-T (INTEGRATED DEVICE TECHNOLOGY INC) 200.4 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 PDF资料下载
参数资料
| 型号： | 950908BGLF-T |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 时钟产生/分配 |
| 英文描述： | 200.4 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 封装： | 0.240 INCH, 0.020 INCH PITCH, GREEN, MO-153, TSSOP-56 |
| 文件页数： | 10/24页 |
| 文件大小： | 305K |
| 代理商： | 950908BGLF-T |
18
Integrated
Circuit
Systems, Inc.
ICS950908
Preliminary Product Preview
0653A—07/26/04
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) serve as dual
signal functions to the device. During initial power-up, they
act as input pins. The logic level (voltage) that is present on
these pins at this time is read and stored into a 5-bit internal
data latch. At the end of Power-On reset, (see AC
characteristics for timing values), the device changes the
mode of operations for these pins to an output function. In
this mode the pins produce the specified buffered clocks to
external loads.
To program (load) the internal configuration register for
these pins, a resistor is connected to either the VDD (logic 1)
power supply or the GND (logic 0) voltage potential. A 10
Kilohm (10K) resistor is used to provide both the solid CMOS
programming voltage needed during the power-up
programming period and to provide an insignificant load on
the output clock during the subsequent operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
W
8.2K
W
Figure 1 shows a means of implementing this function
when a switch or 2 pin header is used. With no jumper is
installed the pin will be pulled high. With the jumper in
place the pin will be pulled low. If programmability is not
necessary, than only a single resistor is necessary. The
programming resistors should be located close to the series
termination resistor to minimize the current loop area. It is
more important to locate the series termination resistor
close to the driver than the programming resistor.
相关PDF资料 |
PDF描述 |
|---|---|
| 950908BFLF | 200.4 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 950908BFLF-T | 200.4 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 08056C103KA74A | General Specifications |
| 950956 | MODULAR TERMINAL BLOCK |
| 950260 | MODULAR TERMINAL BLOCK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9509130000 | 制造商:Weidmuller 功能描述:NPA6 NEXT PADLOCK HASP 制造商:Weidmuller 功能描述:NPA6,NEXT PADLOCK HASP |
| 9509136038 | 制造商:APEM 功能描述:Switch Accessories Led Red/yellow For 1E/1F/1Q/1R |
| 9509136105 | 制造商:APEM 功能描述:Navimec w caps w std legends, up arrow |
| 9509136118 | 制造商:Mec 功能描述:Bulk 制造商:MEC A/S 功能描述:SWITCH MODULE BLACK 制造商:MEC A/S 功能描述:SWITCH MODULE, BLACK 制造商:APEM 功能描述:5 SwitchMountModule w/OK+UP Arrow Legend 制造商:MEC A/S 功能描述:SWITCH, MODULE, 50mA, 24VDC; Contact Voltage DC Nom:24V; Contact Current Max:50mA; Actuator Style:-; Switch Terminals:Solder; Series:Navimec module ;RoHS Compliant: Yes 制造商:MEC 功能描述:Black 5 way PCB mounted switch |
| 9509136119 | 制造商:APEM 功能描述:Navimec w caps w std legends, up arrow/OK |
发布紧急采购，3分钟左右您将得到回复。