- 您现在的位置：买卖IC网 > PDF目录364573 > A29400SERIES 512K X 8 Bit / 256K X 16 Bit CMOS 5.0 Volt-only. Boot Sector Flash Memory PDF资料下载
参数资料
| 型号： | A29400SERIES |
| 英文描述： | 512K X 8 Bit / 256K X 16 Bit CMOS 5.0 Volt-only. Boot Sector Flash Memory |
| 中文描述： | 为512k × 8位/ 256 × 16位的CMOS 5.0伏特只。引导扇区闪存 |
| 文件页数： | 13/33页 |
| 文件大小： | 331K |
| 代理商： | A29400SERIES |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Write Operation Status
A29400 Series
PRELIMINARY (December, 2002, Version 0.2)
13
AMIC Technology, Corp.
Several bits, I/O
2
, I/O
3
, I/O
5
, I/O
6
, I/O
7,
RY/
BY
are provided
in the A29400 to determine the status of a write operation.
Table 6 and the following subsections describe the
functions of these status bits. I/O
7
, I/O
6
and RY/
BY
each
offer a method for determining whether a program or erase
operation is complete or in progress. These three bits are
discussed first.
I/O
7
:
Data
Polling
The
Data
Polling bit, I/O
7
, indicates to the host system
whether an Embedded Algorithm is in progress or
completed, or whether the device is in Erase Suspend.
Data
Polling is valid after the rising edge of the final
WE
pulse in the program or erase command sequence.
During the Embedded Program algorithm, the device
outputs on I/O
7
the complement of the datum programmed
to I/O
7
. This I/O
7
status also applies to programming during
Erase Suspend. When the Embedded Program algorithm
is complete, the device outputs the datum programmed to
I/O
7
. The system must provide the program address to
read valid status information on I/O
7
. If a program address
falls within a protected sector,
Data
Polling on I/O
7
is
active for approximately 2
μ
s, then the device returns to
reading array data.
During the Embedded Erase algorithm,
Data
Polling
produces a "0" on I/O
7
. When the Embedded Erase
algorithm is complete, or if the device enters the Erase
Suspend mode,
Data
Polling produces a "1" on I/O
7
.This
is analogous to the complement/true datum output
described for the Embedded Program algorithm: the erase
function changes all the bits in a sector to "1"; prior to this,
the device outputs the "complement," or "0." The system
must provide an address within any of the sectors selected
for erasure to read valid status information on I/O
7
.
After an erase command sequence is written, if all sectors
selected for erasing are protected,
Data
Polling on I/O
7
is
active for approximately 100
μ
s, then the device returns to
reading array data. If not all selected sectors are protected,
the Embedded Erase algorithm erases the unprotected
sectors, and ignores the selected sectors that are
protected.
When the system detects I/O
7
has changed from the
complement to true data, it can read valid data at I/O
7
- I/O
0
on the following read cycles. This is because I/O
7
may
change asynchronously with I/O
0
- I/O
6
while Output Enable
(
OE
) is asserted low. The
Data
Polling Timings (During
Embedded Algorithms) figure in the "AC Characteristics"
section illustrates this. Table 6 shows the outputs for
Data
Polling on I/O
7
. Figure 4 shows the
Data
Polling algorithm.
START
Read I/O
7
-I/O
0
Address = VA
I/O
7
= Data
FAIL
No
Note :
1. VA = Valid address for programming. During a sector
erase operation, a valid address is an address within any
sector selected for erasure. During chip erase, a valid
address is any non-protected sector address.
2. I/O
7
should be rechecked even if I/O
5
= "1" because
I/O
7
may change simultaneously with I/O
5
.
No
Read I/O
7
- I/O
0
Address = VA
I/O
5
= 1
I/O
7
= Data
Yes
No
PASS
Yes
Yes
Figure 4. Data Polling Algorithm
相关PDF资料 |
PDF描述 |
|---|---|
| A29800SERIES | 1024K X 8 Bit / 512K X 16 Bit CMOS 5.0 Volt-only. Boot Sector Flash Memory |
| A2982ELW | Octal Peripheral Driver |
| A2982SLWTR | Octal Peripheral Driver |
| A2982 | 8-CHANNEL SOURCE DRIVERS |
| A2982SLW | 8-CHANNEL SOURCE DRIVERS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A29400TM-55 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:512K X 8 Bit / 256K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29400TM-70 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:512K X 8 Bit / 256K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29400TM-90 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:512K X 8 Bit / 256K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29400TV-55 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:512K X 8 Bit / 256K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| A29400TV-70 | 制造商:AMICC 制造商全称:AMIC Technology 功能描述:512K X 8 Bit / 256K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
发布紧急采购，3分钟左右您将得到回复。