参数资料
| 型号： | A42MX09-3VQG100I |
| 厂商： | Microsemi SoC |
| 文件页数： | 76/142页 |
| 文件大小： | 0K |
| 描述： | IC FPGA MX SGL CHIP 14K 100VQFP |
| 标准包装： | 90 |
| 系列： | MX |
| 输入/输出数： | 83 |
| 门数： | 14000 |
| 电源电压： | 3 V ~ 3.6 V，4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 100-TQFP |
| 供应商设备封装： | 100-VQFP（14x14） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页当前第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页
40MX and 42MX FPGA Families
Re vi s i on 11
1 - 35
Predictable Performance: Tight Delay Distributions
Propagation delay between logic modules depends on the resistive and capacitive loading of the routing
tracks, the interconnect elements, and the module inputs being driven. Propagation delay increases as
the length of routing tracks, the number of interconnect elements, or the number of inputs increases.
From a design perspective, the propagation delay can be statistically correlated or modeled by the fanout
(number of loads) driven by a module. Higher fanout usually requires some paths to have longer routing
tracks.
The MX FPGAs deliver a tight fanout delay distribution, which is achieved in two ways: by decreasing the
delay of the interconnect elements and by decreasing the number of interconnect elements per path.
Microsemi’s patented antifuse offers a very low resistive/capacitive interconnect. The antifuses,
fabricated in 0.45 m lithography, offer nominal levels of 100
Ω resistance and 7.0 fF capacitance per
antifuse.
MX fanout distribution is also tight due to the low number of antifuses required for each interconnect
path. The proprietary architecture limits the number of antifuses per path to a maximum of four, with
90 percent of interconnects using only two antifuses.
Timing Characteristics
Device timing characteristics fall into three categories: family-dependent, device-dependent, and design-
dependent. The input and output buffer characteristics are common to all MX devices. Internal routing
delays are device-dependent; actual delays are not determined until after place-and-route of the user's
design is complete. Delay values may then be determined by using the Designer software utility or by
performing simulation with post-layout delays.
Critical Nets and Typical Nets
Propagation delays are expressed only for typical nets, which are used for initial design performance
evaluation. Critical net delays can then be applied to the most timing critical paths. Critical nets are
determined by net property assignment in Microsemi's Designer software prior to placement and routing.
Up to 6% of the nets in a design may be designated as critical.
Long Tracks
Some nets in the design use long tracks, which are special routing resources that span multiple rows,
columns, or modules. Long tracks employ three and sometimes four antifuse connections, which
increase capacitance and resistance, resulting in longer net delays for macros connected to long tracks.
Typically, up to 6 percent of nets in a fully utilized device require long tracks. Long tracks add
approximately a 3 ns to a 6 ns delay, which is represented statistically in higher fanout (FO=8) routing
delays in the data sheet specifications section, shown in Table 1-28 on page 1-40.
Timing Derating
MX devices are manufactured with a CMOS process. Therefore, device performance varies according to
temperature, voltage, and process changes. Minimum timing parameters reflect maximum operating
voltage, minimum operating temperature and best-case processing. Maximum timing parameters reflect
minimum operating voltage, maximum operating temperature and worst-case processing.
相关PDF资料 |
PDF描述 |
|---|---|
| A42MX09-3VQ100I | IC FPGA MX SGL CHIP 14K 100VQFP |
| EPF10K30AQC208-2N | IC FLEX 10KA FPGA 30K 208-PQFP |
| EPF10K30AQC208-2 | IC FLEX 10KA FPGA 30K 208-PQFP |
| EPF10K30ATI144-3N | IC FLEX 10KA FPGA 30K 144-TQFP |
| EPF10K30ATI144-3 | IC FLEX 10KA FPGA 30K 144-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A42MX09-BG100 | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:40MX and 42MX FPGA Families |
| A42MX09-BG100ES | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:40MX and 42MX FPGA Families |
| A42MX09-BG100I | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:40MX and 42MX FPGA Families |
| A42MX09-BG100M | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:40MX and 42MX FPGA Families |
| A42MX09-CQ100 | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:40MX and 42MX FPGA Families |
发布紧急采购，3分钟左右您将得到回复。