- 您现在的位置：买卖IC网 > PDF目录1773 > A4980KLPTR-T (Allegro Microsystems Inc)IC STEPPER DVR PROGR 28-TSSOP PDF资料下载
参数资料
| 型号： | A4980KLPTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 24/44页 |
| 文件大小： | 0K |
| 描述： | IC STEPPER DVR PROGR 28-TSSOP |
| 标准包装： | 1 |
| 应用： | 步进电机驱动器 |
| 输出数： | 1 |
| 电流 - 输出： | ±1.4A |
| 电压 - 负载： | 0 V ~ 50 V |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 包装： | 标准包装 |
| 其它名称： | 620-1461-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
A4980
Automotive, Programmable Stepper Driver
In half step and in quarter step, the single phase active positions
control the output of the A4980:
are used to preserve symmetry. However, if the motor is required
to stop with a significant holding torque for any length of time
it is recommended that the 45° positions be used; those are Step
Angle Numbers 8, 24, 40, and 56, as used with full-step resolu-
tion.
The following table summarizes the Step Angle Numbers used
for the four resolutions available when using the STEP input to
Mode
Full
Half
Quarter
Sixteenth
Step Angle Numbers used
8, 24, 40, 56
0, 8, 16, 24, 32, 40, 48, 56
0, 4, 8, 12, 16, 20, 24, 28, 32,
36, 40, 44, 48, 52, 56, 60
All
The microstep select inputs can be changed between each rising
I A
edge of the STEP input. The only restriction is that the MSO and
MS1 logic inputs must comply with the set-up and hold timing
24
40
8
56
I B
constraints. When the microstep resolution changes, the A4980
moves to the next available Step Angle Number on the next rising
edge of the STEP input. For example, if the microstep mode is
sixteenth and the present Step Angle Number is 59, then with the
direction forwards (increasing Step Angle Number), changing
to quarter step mode will cause the phase number to go to 60 on
the next rising edge of the STEP input. If instead the microstep
mode is changed to half step then the phase number will go to 0
on the next rising edge of the STEP input. If the microstep mode
Figure 7. Full-step phase diagram using STEP input
I A
16
is changed to full step then the phase number will go to 8 on the
next rising edge of the STEP input.
Control Through the Serial Interface
24
8
The A4980 provides the ability to directly control the motor
movement using only the serial interface. In fact, all features
32
0
I B
of the A4980, except sleep mode, can be controlled through the
serial interface thus removing the requirement for individual
control inputs. This can reduce the interface requirement from
multiple I/O signals to a single four wire interface.
40
56
Motor movement is controlled using the serial interface by
48
Figure 8. Half-step phase diagram using STEP input
I A
increasing or decreasing the Step Angle Number. Note that the
maximum value of the Step Angle Number is 63 and the mini-
mum number is 0.Therefore, any increase or decrease in the
microstep number is performed using modulo 64 arithmetic. This
24
20
16
12
8
means that increasing a Step Angle Number of 63 by 1 will pro-
duce a Step Angle Number of 0. Increasing by two from 63 will
produce 1 and so on. Similarly in the reverse direction, decreasing
28
4
a Step Angle Number of 0 by 1 will produce a Step Angle Num-
32
0
I B
ber of 63. Decreasing by two from 0 will produce 62 and so on.
The least significant six bits of the Run register, bits 0 to 5, are
36
40
56
60
the step change number, SC[5..0]. This number is a two’s comple-
ment number that is added to the Step Angle Number causing it
44 52
48
Figure 9. Quarter-step phase diagram using STEP input
to increase or decrease. Two’s complement is the natural integer
number system for most microcontrollers. This allows standard
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
24
相关PDF资料 |
PDF描述 |
|---|---|
| A4982SLPTR-T | IC DRIVER MICROSTEPPING 24-TSSOP |
| A4983SETTR-T | IC MOTOR DRIVER MICROSTEP 28-QFN |
| A4984SLPTR-T | IC STEPPER MOTOR DRIVER 24TSSOP |
| A4985SETTR-T | IC STEPPER MOTOR DRIVER 32QFN |
| A4986SLPTR-T | IC PWM MOTOR DRIVER 24TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A4982 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:DMOS Microstepping Driver with Translator And Overcurrent Protection |
| A4982_V4 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:DMOS Microstepping Driver with Translator And Overcurrent Protection |
| A49821 | 制造商:TE Connectivity 功能描述:Triquint value add services |
| A4982SETTR-T | 功能描述:IC STEPPER MOTOR DRIVER 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A4982SLPTR | 制造商:Allegro MicroSystems LLC 功能描述:DMOS Microstepping Driver |
发布紧急采购，3分钟左右您将得到回复。