参数资料
型号: A4980KLPTR-T
厂商: Allegro Microsystems Inc
文件页数: 29/44页
文件大小: 0K
描述: IC STEPPER DVR PROGR 28-TSSOP
标准包装: 1
应用: 步进电机驱动器
输出数: 1
电流 - 输出: ±1.4A
电压 - 负载: 0 V ~ 50 V
电源电压: 3 V ~ 5.5 V
工作温度: -40°C ~ 150°C
安装类型: 表面贴装
封装/外壳: 28-SOIC(0.173",4.40mm 宽)裸露焊盘
供应商设备封装: 28-TSSOP 裸露焊盘
包装: 标准包装
其它名称: 620-1461-6
A4980
Automotive, Programmable Stepper Driver
Each of the 16 values written to the phase table is a 6-bit num-
ber that determines the current trip point for the associated step.
The highest value, 63, represents the maximum phase current,
I PMAX , defined in the section of the specification on phase cur-
rent control. Other numbers represent a percentage of I PMAX . For
example, the number 23 sets the phase current trip point to 23/63
= 36.51% of I PMAX .
There are two restrictions when using the phase table load capa-
bility:
? The required current profile must conform to the symmetry
shown in figure 12. The forward (positive) current part must be
symmetrical about Step Angle Number16 for phase A and about
0 for phase B. The reverse (negative) current part must be sym-
metrical about Step Angle Number 48 for phase A and about 32
for phase B. The forward and reverse profiles for each phase
must be the same.
? The phase current must be zero at Step Angle Numbers 0 and 32
for phase A and Step Angle Numbers 16 and 48 for phase B.
Figure 13. Example current profile
Phase Current Table Programming Example
As an example of programming the phase current table, consider
the current profile shown in figure 13. This shows a profile where
the torque from each phase is required to be relatively higher
at the detent points, that is, the points where only one phase is
active. (This current profile does not relate to any specific motor,
it is only shown as an example.)
Figure 13 shows the required current for each phase at each
Step Angle Number as a percentage of the maximum phase
current, I PMAX , defined above. The waveform conforms to the
required symmetry and zero crossing restrictions, so the profile
for phase A for Step Angle Numbers from 0 to 16 (outlined and
shaded) can be used to determine the phase table contents.
The first step is to digitize the profile into microsteps and the
percentage values into 6-bit numbers, as shown in figure 14.
At each of the one-sixteenth microsteps, identified by Step Angle
Number, the value of the phase current, as a percentage of the
maximum phase current, I PMAX , is digitized to a 6-bit value from
0 to 63. The value 63 represents 100% of I PMAX , 32 represents
Figure 14. Digitizing the example current profile
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
29
相关PDF资料
PDF描述
A4982SLPTR-T IC DRIVER MICROSTEPPING 24-TSSOP
A4983SETTR-T IC MOTOR DRIVER MICROSTEP 28-QFN
A4984SLPTR-T IC STEPPER MOTOR DRIVER 24TSSOP
A4985SETTR-T IC STEPPER MOTOR DRIVER 32QFN
A4986SLPTR-T IC PWM MOTOR DRIVER 24TSSOP
相关代理商/技术参数
参数描述
A4982 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:DMOS Microstepping Driver with Translator And Overcurrent Protection
A4982_V4 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:DMOS Microstepping Driver with Translator And Overcurrent Protection
A49821 制造商:TE Connectivity 功能描述:Triquint value add services
A4982SETTR-T 功能描述:IC STEPPER MOTOR DRIVER 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器,驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器,步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP(0.295",7.50mm 宽) 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR
A4982SLPTR 制造商:Allegro MicroSystems LLC 功能描述:DMOS Microstepping Driver