- 您现在的位置：买卖IC网 > PDF目录14407 > A8698ELJTR-T (Allegro Microsystems Inc)IC REG BUCK ADJ 3A 8SOIC PDF资料下载
参数资料
| 型号： | A8698ELJTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 7/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 3A 8SOIC |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 20 V |
| 输入电压： | 8 V ~ 25 V |
| PWM 型： | 电流模式 |
| 电流 - 输出： | 3A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-SOIC-EP |
| 产品目录页面： | 1142 (CN2011-ZH PDF) |
| 其它名称： | 620-1177-6 |
A8698
Wide Input Voltage 3.0 A Step Down Regulator
Functional Description
t OFF = R SET ?
? 1–0.03 V BIAS ?
?
?
?
TheA8698 is a fixed off-time, current-mode–controlled buck
switching regulator. The regulator requires an external clamping
diode, inductor, and filter capacitor, and operates in both continu-
ous and discontinuous modes. An internal blanking circuit is used
to filter out transients resulting from the reverse recovery of the
external clamp diode. Typical blanking time is 200 ns.
The value of a resistor between the TSET pin and ground deter-
mines the fixed off-time (see graph in the t OFF section).
V OUT . The output voltage is adjustable from 0.8 to 20 V, based on
the combination of the value of the external resistor divider and
the internal 0.8 V ±2% reference. The voltage can be calculated
with the following formula:
V OUT = V FB × (1 + R1/R2) (1)
Light Load Regulation. To maintain voltage regulation during
light load conditions, the switching regulator enters a cycle-skip-
ping mode. As the output current decreases, there remains some
energy that is stored during the power switch minimum on-time.
In order to prevent the output voltage from rising, the regulator
skips cycles once it reaches the minimum on-time, effectively
making the off-time larger.
Soft Start. An internal ramp generator and counter allow the out-
put to slowly ramp up. This limits the maximum demand on the
ON/OFF Control. The ENB pin is externally pulled to ground
to enable the device and begin the soft start sequence. When the
ENB is open circuited, the switcher is disabled and the output
decays to 0 V.
Protection. The buck switch will be disabled under one or more
of the following fault conditions:
? V IN < 6 V
? ENB pin = open circuit
? TSD fault
When the device comes out of a TSD fault, it will go into a soft
start to limit inrush current.
t OFF . The value of a resistor between the TSET pin and ground
determines the fixed off-time. The formula to calculate t OFF ( μ s)
is:
(2)
10.2 × 10 9
where R TSET (k Ω ) is the value of the resistor. Results with the
VBIAS pin connected are shown in the following graph (when
VBIAS is not connected, use V BIAS = 0 in equation 2):
Off-Time Setting versus Resistor Value
200
180
160
external power supply by controlling the inrush current required
to charge the external capacitor and any dc load at startup.
Internally, the ramp is set to 10 ms nominal rise time. During soft
start, current limit is 3.5 A minimum.
The following conditions are required to trigger a soft start:
140
120
100
80
60
40
V BIAS = 5 V
V BIAS = 3.3 V
? V IN > 6 V
? ENB pin input falling edge
? Reset of a TSD (thermal shut down) event
20
0
1
2
3
4
5
6
7 8 9
t OFF (μs)
10
11 12 13 14 15
16
V BIAS . To improve overall system efficiency, the regulator output,
V OUT , is connected to the VBIAS input to supply the operating
bias current during normal operating conditions. During startup
t ON . From the volt-second balance of the inductor, the turn-on
time, t on , can be calculated approximately by the equation:
the circuitry is run off of the VIN supply. VBIAS should be con-
nected to VOUT when the V OUT target level is between 3.3 and
5 V. If the output voltage is less than 3.3 V, then the A8698 can
t ON =
( V OUT + V f + I OUT R L ) t OFF
V IN – I OUT R DS(on) – I OUT R L – V OUT
(3)
operate with an internal supply and pay a penalty in efficiency,
as the bias current will come from the high voltage supply, VIN.
VBIAS can also be supplied with an external voltage source. No
power-up sequencing is required for normal opperation.
where
V f is the voltage drop across the external Schottky diode,
R L is the winding resistance of the inductor, and
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| GMM11DRAS | CONN EDGECARD 22POS R/A .156 SLD |
| GBM43DCWT | CONN EDGECARD 86POS DIP .156 SLD |
| GCA30DTKT | CONN EDGECARD 60POS DIP .125 SLD |
| PQ1CG38M2FZH | IC REG BUCK INV ADJ 0.8A TO220 |
| RBC35DREI-S93 | CONN EDGECARD 70POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A-869-M | 功能描述:端子 DISC MFG 07/01 22-18 MALE BLT DISC RoHS:否 制造商:AVX 产品:Junction Box - Wire to Wire 系列:9826 线规:26-18 接线柱/接头大小: 绝缘: 颜色:Red 型式:Female 触点电镀:Tin over Nickel 触点材料:Beryllium Copper, Phosphor Bronze 端接类型:Crimp |
| A-869T | 制造商:ETC MOLEX-INACTIVE 功能描述:Cross Referenced to MOLEX - Part: MOL19036-0005 |
| A86M | 制造商:Thomas & Betts 功能描述:TERMINAL BELT ASSY |
| A86M3E | 制造商:Pentair Technical Products / Hoffman 功能描述:Type 12 Encl. 86.13x112.00x14. , 86.12x112.00x14.12, Steel |
| A-86M3E | 制造商:Pentair Technical Products / Hoffman 功能描述:Type 12 Encl. 86.13x112.00x14. |
发布紧急采购，3分钟左右您将得到回复。