- 您现在的位置：买卖IC网 > PDF目录10031 > AD1555BPZRL (Analog Devices Inc)IC ADC PGA 24BIT LN 28-PLCC PDF资料下载
参数资料
| 型号： | AD1555BPZRL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC PGA 24BIT LN 28-PLCC |
| 标准包装： | 1 |
| 位数： | 24 |
| 采样率（每秒）： | 256k |
| 数据接口： | 串行，并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 96mW |
| 电压电源： | 双 ± |
| 工作温度： | -55°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-LCC（J 形引线） |
| 供应商设备封装： | 28-PLCC（11.51x11.51） |
| 包装： | 标准包装 |
| 输入数目和类型： | 1 个差分，双极 |
| 其它名称： | AD1555BPZRLDKR |
REV. B
AD1555/AD1556
–20–
RESET Operation
The RESET pin initializes the AD1556 in a known state.
RESET is active on the next CLKIN rising edge after the
RESET input is brought high as shown in Figure 4. The reset
value of each bit of the configuration and the status registers are
indicated in Table V and Table VIII. The filter memories are
not cleared by the reset. Filter convolutions begin on the next
CLKIN rising edge after the RESET input is returned low. A
RESET operation is done on power-up, independent of the
RESET pin state.
In multiple ADCs applications where absolute synchroniza-
tion—even below the noise floor—is required, RESETD, which
resets the decimator, can be tied to RESET to ensure this
synchronization.
Power-Down Operation
The PWRDN pin puts the AD1556 in a power-down state.
PWRDN is active on the next CLKIN rising edge after the
PWRDN input is brought high. While in this state, MCLK is
held at a fixed level and the AD1555 is therefore powered
down too. The serial interface remains active allowing read and
write operations of the AD1556. The configuration and status
registers maintain their content during the power-down state.
SYNC Operation
SYNC is used to create a relationship between the analog input
signal and the output samples of the AD1556. The SYNC event
does two things:
It synchronizes the AD1555 clock, MCLK, to the AD1556
clock, CLKIN, as shown in Figure 3.
It clears the filter and then initiates the filter convolution.
Exactly one sampling rate delay later, the DRDY pin goes
high. A SYNC event occurs on the next CLKIN rising edge
after the SYNC input is brought high as shown in Figure 3.
The DRDY output goes high on the next falling edge of
CLKIN. SYNC may be applied once or kept high, or applied
synchronously at the output word rate, all with the same effect.
Configuring and Interfacing the AD1556
The AD1556 configuration can be loaded either by hardware
(H/
S pin high) or via the serial interface of the AD1556 (H/S
pin low). To operate with the AD1556, the CLKIN clock must be
kept running at the nominal frequency of 1.024 MHz. Table V
gives the description of each bit of the configuration register and
Table VI defines the selection of the filter bandwidth. When the
software mode is selected (H/
S pin low), the configuration register
is loaded using the pins DIN, SCLK,
CS, and R/W. In this mode,
when RESET is active, the configuration register mimics the selec-
tion of the hardware pins. The AD1556 and the AD1555 can be
put in power-down by software.
The DRDYBUF bit controls the operating mode of the DRDY
output pin. When the DRDYBUF bit is low, the DRDY is a con-
ventional CMOS push-pull output buffer as shown in Figure 11.
When the DRDYBUF bit is high, the DRDY output pin is an
open drain PMOS pull-up as shown in Figure 11. Many DRDY
pins may be connected with an external pull-down resistor in a
wired OR to minimize the interconnection between the AD1556s
and the microprocessor in multichannel applications. The DRDY
pin is protected against bit contention.
By connecting DRDY to RSEL directly, and applying 48 SCLK
cycles, both data and status can be read sequentially, data
register first.
Table VI. Filter Bandwidth Selection
BW2
BW1
BW0
Output Rate (ms)
00
0
4
00
1
2
01
0
1
01
1
1/2
10
0
1/4
10
1
1/8
11
0
1/16
11
1Reserved
Table V. Configuration Register Data Bits
Bit
Number
Name
Description
RESET State
DB15 (MSB)
X
DB14
X
DB13
X
DB12
X
DB11
PWRDN
Power-Down Mode
PWRDN
DB10
CSEL
Select TDATA Input
CSEL
DB9
X
DB8
BW2
Filter Bandwidth Selection
BW2
DB7
BW1
Filter Bandwidth Selection
BW1
DB6
BW0
Filter Bandwidth Selection
BW0
DB5
DRDYBUF
DRDY Output Mode
0 (Push-Pull)
DB4
CB4
PGA Input Select
PGA4
DB3
CB3
PGA Input Select
PGA3
DB2
CB2
PGA Gain Select
PGA2
DB1
CB1
PGA Gain Select
PGA1
DB0 (LSB)
CB0
PGA Gain Select
PGA0
相关PDF资料 |
PDF描述 |
|---|---|
| VI-26M-MX-F1 | CONVERTER MOD DC/DC 10V 75W |
| AD678AJ | IC ADC 12BIT 200KSPS 44-JLCC |
| IDT72V3611L15PF8 | IC FIFO SYNC 64X36 15NS 120-TQFP |
| MS27468T21A16P | CONN RCPT 16POS JAM NUT W/PINS |
| MS27468E21A16P | CONN RCPT 16POS JAM NUT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD1556 | 制造商:AD 制造商全称:Analog Devices 功能描述:24-Bit ADC WITH LOW NOISE PGA |
| AD1556AS | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 256ksps 24-bit Parallel/Serial 44-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD1556ASRL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 256ksps 24-bit Parallel/Serial 44-Pin MQFP T/R |
| AD1556ASZ | 功能描述:IC ADC PGA 24BIT LN 44MQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD1556ASZRL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 256ksps 24-bit Parallel/Serial 44-Pin MQFP T/R |
发布紧急采购，3分钟左右您将得到回复。