参数资料
型号: AD1838AASZ-REEL
厂商: Analog Devices Inc
文件页数: 11/24页
文件大小: 0K
描述: IC CODEC 2ADC/6DAC 24 BIT 52MQFP
标准包装: 800
类型: 立体声音频
数据接口: 串行
分辨率(位): 24 b
ADC / DAC 数量: 2 / 6
三角积分调变:
S/N 比,标准 ADC / DAC (db): 105 / 108
动态范围,标准 ADC / DAC (db): 105 / 108
电压 - 电源,模拟: 4.5 V ~ 5.5 V
电压 - 电源,数字: 4.5 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 52-QFP
供应商设备封装: 52-MQFP(10x10)
包装: 带卷 (TR)
REV. A
AD1838A
–19–
CONTROL/STATUS REGISTERS
The AD1838A has 13 control registers, 11 of which are used to set
the operating mode of the part. The other two registers, ADC Peak
0 and ADC Peak 1, are read-only and should not be programmed.
Each of the registers is 10 bits wide with the exception of the ADC
peak reading registers, which are 6 bits wide. Writing to a con-
trol register requires a 16-bit data frame to be transmitted. Bits
15 to 12 are the address bits of the required register. Bit 11 is a
read/write bit. Bit 10 is reserved and should always be programmed
to 0. Bits 9 to 0 contain the 10-bit value that is to be written to
the register or, in the case of a read operation, the 10-bit register
contents. Figure 3 shows the format of the SPI read and write
operation.
DAC Control Registers
The AD1838A register map has eight registers that are used
to control the functionality of the DAC section of the part.
The function of the bits in these registers is discussed below.
Sample Rate
These bits control the sample rate of the DACs. Based on a
24.576 MHz IMCLK, sample rates of 48 kHz, 96 kHz, and
192 kHz are available. The MCLK scaling bits in ADC Con-
trol Register 3 should be programmed appropriately, based
on the master clock frequency.
Power-Down/Reset
This bit controls the power-down status of the DAC section.
By default, normal mode is selected. But by setting this bit, the
digital section of the DAC stage can be put into a low power
mode, thus reducing the digital current. The analog output
section of the DAC stage is not powered down.
DAC Data-Word Width
These two bits set the word width of the DAC data. Compact
disk (CD) compatibility may require 16 bits, but many modern
digital audio formats require 24-bit sample resolution.
DAC Data Format
The AD1838A serial data interface can be configured to be
compatible with a choice of popular interface formats, including
I
2S, LJ, RJ, or DSP modes. Details of these interface modes
are given in the Serial Data Port section.
De-emphasis
The AD1838A provides built-in de-emphasis filtering for the
three standard sample rates of 32.0 kHz, 44.1 kHz, and 48 kHz.
Mute DAC
Each of the six DACs in the AD1838A has its own independent
mute control. Setting the appropriate bit mutes the DAC
output. The AD1838A uses a clickless mute function that attenu-
ates the output to approximately –100 dB over a number of cycles.
Stereo Replicate
Setting this bit copies the digital data sent to the stereo pair
DAC1 to the three other stereo DACs in the system. This
allows all three stereo DACs to be driven by one digital data
stream. Note that in this mode, DAC data sent to the other
DACs is ignored.
DAC Volume Control
Each DAC in the AD1838A has its own independent volume
control. The volume of each DAC can be adjusted in 1024
linear steps by programming the appropriate register. The
default value for this register is 1023, which provides no attenu-
ation, i.e., full volume.
ADC Control Registers
The AD1838A register map has five registers that are used to
control the functionality and to read the status of the ADCs. The
function of the bits in each of these registers is discussed below.
ADC Peak Level
These two registers store the peak ADC result from each channel
when the ADC peak readback function is enabled. The peak
result is stored as a 6-bit number from 0 dB to –63 dB in 1 dB
steps. The value contained in the register is reset once it has been
read, allowing for continuous level adjustment as required. Note
that the ADC peak level registers use the 6 MSB in the register
to store the results.
Sample Rate
This bit controls the sample rate of the ADCs. Based on a
24.576 MHz IMCLK, sample rates of 48 kHz and 96 kHz are
available. The MCLK scaling bits in ADC Control Register 3
should be programmed appropriately based on the master clock
frequency.
ADC Power-Down
This bit controls the power-down status of the ADC section and
operates in a similar manner to the DAC power-down.
High-Pass Filter
The ADC signal path has a digital high-pass filter. Enabling this
filter removes the effect of any dc offset in the analog input
signal from the digital output codes.
ADC Data-Word Width
These two bits set the word width of the ADC data.
ADC Data Format
The AD1838A serial data interface can be configured to be
compatible with a choice of popular interface formats, including
I
2S, LJ, RJ, or DSP modes.
Master/Slave Auxiliary Mode
When the AD1838A is operating in the auxiliary mode, the auxil-
iary ADC control pins, AUXBCLK and AUXLRCLK, which
connect to the external ADCs, can be set to operate as a master
or slave. If the pins are set in slave mode, one of the external
ADCs should provide the LRCLK and BCLK signals.
ADC Peak Readback
Setting this bit enables ADC peak reading. See the ADCs section
for more information.
相关PDF资料
PDF描述
AD1835AASZ-REEL IC CODEC 2ADC/8DAC 24BIT 52MQFP
ADAV803ASTZ-REEL IC CODEC AUDIO R-DVD 3.3V 64LQFP
AD1939YSTZRL IC CODEC 24BIT ADC/DAC 64-LQFP
AD1937WBSTZ-RL IC CODEC 4/ADC DIFF OUT 64-LQFP
AD1938WBSTZ-RL IC CODEC 24BIT 4ADC/8DAC 48LQFP
相关代理商/技术参数
参数描述
AD1838AS 制造商:Analog Devices 功能描述:Audio Codec 2ADC / 6DAC 24-Bit 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:- Bulk
AD1838AS-REEL 制造商:Analog Devices 功能描述:Audio Codec 2ADC / 6DAC 24-Bit 52-Pin MQFP T/R 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel
AD1839 制造商:AD 制造商全称:Analog Devices 功能描述:2 ADC, 6 DAC, 96 kHz, 24-Bit sigma-delta Codec
AD1839A 制造商:AD 制造商全称:Analog Devices 功能描述:2 ADC, 6 DAC, 96 kHz, 24-Bit Sigma-Delta Codec
AD1839AAS 制造商:Analog Devices 功能描述:Audio Codec 2ADC / 6DAC 24-Bit 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:HIGH PERFORMANCE CODEC I.C. - Bulk 制造商:Analog Devices 功能描述:IC CODEC SMD 1839 MQFP52