- 您现在的位置：买卖IC网 > PDF目录9288 > AD5233BRUZ10-R7 (Analog Devices Inc)IC DGTL POT QUAD 64POS 24-TSSOP PDF资料下载
参数资料
| 型号： | AD5233BRUZ10-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/32页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT QUAD 64POS 24-TSSOP |
| 标准包装： | 1,000 |
| 接片： | 64 |
| 电阻（欧姆）： | 10k |
| 电路数： | 4 |
| 温度系数： | 标准值 600 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 2.7 V ~ 5.5 V，±2.25 V ~ 2.75 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD5233
Rev. B | Page 15 of 32
THEORY OF OPERATION
The AD5233 digital potentiometer is designed to operate as a
true variable resistor replacement device for analog signals that
remain within the terminal voltage range of VSS < VTERM < VDD.
The basic voltage range is limited to VDD VSS < 5.5 V. The
digital potentiometer wiper position is determined by the
RDAC register contents.
The RDAC register acts as a scratchpad register, allowing as
many value changes as necessary to place the potentiometer
wiper in the correct position. The scratchpad register can be
programmed with any position value using the standard SPI
serial interface mode by loading the complete representative
data-word. Once a desirable position is found, this value can be
stored in an EEMEM register. Thereafter, the wiper position is
always restored to that position for subsequent power-up.
The EEMEM data storing process takes approximately 25 ms;
during this time, the shift register is locked, preventing any
changes from taking place. The RDY pin pulses low to indicate
the completion of this EEMEM storage.
The following instructions facilitate the user’s programming
needs (see Table 7 for details):
0 = Do nothing.
1 = Restore EEMEM contents to RDAC.
2 = Store RDAC setting to EEMEM.
3 = Store RDAC setting or user data to EEMEM.
4 = Decrement 6 dB.
5 = Decrement all 6 dB.
6 = Decrement one step.
7 = Decrement all one step.
8 = Reset EEMEM contents to RDACs.
9 = Read EEMEM contents from SDO.
10 = Read RDAC wiper setting from SDO.
11 = Write data to RDAC.
12 = Increment 6 dB.
13 = Increment all 6 dB.
14 = Increment one step.
15 = Increment all one step.
SCRATCHPAD AND EEMEM PROGRAMMING
The scratchpad RDAC register directly controls the position of
the digital potentiometer wiper. For example, when the scratchpad
register is loaded with all 0, the wiper is connected to Terminal
B of the variable resistor. The scratchpad register is a standard
logic register with no restriction on the number of changes
allowed, but the EEMEM registers have a program erase/write
cycle limitation (see the Flash/EEMEM Reliability section).
BASIC OPERATION
The basic mode of setting the variable resistor wiper position
(programming the scratchpad register) is accomplished by
loading the serial data input register with Instruction 11,
Address A1, Address A0, and the desired wiper position
data. When the proper wiper position is determined, the
user can load the serial data input register with Instruction 2,
which stores the wiper position data in the EEMEM register.
After 25 ms, the wiper position is permanently stored in the
nonvolatile memory location. Table 5 provides a programming
example listing the sequence of serial data input (SDI) words
with the serial data output appearing at the SDO pin in
hexadecimal format.
Table 5. Set and Store RDAC Data to EEMEM Register
SDI
SDO
Action
0xB010
0xXXXX
Writes Data 0x10 to the RDAC1 register,
Wiper W1 moves to full-scale position.
0x20XX
0xB010
Stores RDAC1 register content into the
EEMEM1 register.
At system power-on, the scratchpad register is automatically
refreshed with the value previously stored in the EEMEM
register. The factory-preset EEMEM value is midscale, but it
can be changed by the user thereafter.
During operation, the scratchpad (RDAC) register can be
refreshed with the EEMEM register data with Instruction 1 or
Instruction 8. The RDAC register can also be refreshed with the
EEMEM register data under hardware control by pulsing the PR
pin. The PR pulse first sets the wiper at midscale when brought
to Logic 0, and then, on the positive transition to Logic 1, it
reloads the RDAC wiper register with the contents of EEMEM.
Many additional advanced programming commands are
available to simplify the variable resistor adjustment process
(see Table 7). For example, the wiper position can be changed
one step at a time using the increment/decrement instruction or
by 6 dB with the shift left/right instruction. Once an increment,
decrement, or shift instruction has been loaded into the shift
register, subsequent CS strobes can repeat this command.
A serial data output SDO pin is available for daisy-chaining and
for readout of the internal register contents.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27484E16F35SD | CONN PLUG 55POS STRAIGHT W/SCKT |
| DS1100LZ-30+T | IC DELAY LINE 5TAP 30NS 8-SOIC |
| VI-B4Z-MW-F1 | CONVERTER MOD DC/DC 2V 40W |
| VI-B4Y-MY-F1 | CONVERTER MOD DC/DC 3.3V 33W |
| DS1100LZ-50+T | IC DELAY LINE 5TAP 50NS 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5233BRUZ50 | 功能描述:IC POT QUAD 50K 64POS 24-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5233BRUZ50-R7 | 功能描述:IC DGTL POT QUAD 64POS 24-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD5235 | 制造商:AD 制造商全称:Analog Devices 功能描述:8-Bit Dual Nonvolatile Memory Digital Potentiometer |
| AD5235BRU25 | 制造商:Analog Devices 功能描述:Digital Potentiometer 1024POS 25KOhm Dual 16-Pin TSSOP 制造商:Analog Devices 功能描述:IC DIGITAL POT 25KOHM 1024 DUAL 16-TSSO |
| AD5235BRU250 | 制造商:Analog Devices 功能描述:Digital Potentiometer 1024POS 250KOhm Dual 16-Pin TSSOP 制造商:Analog Devices 功能描述:IC DUAL DIGITAL POT. 10-BIT |
发布紧急采购，3分钟左右您将得到回复。