- 您现在的位置：买卖IC网 > PDF目录9308 > AD5274BCPZ-20-RL7 (Analog Devices Inc)IC RHEOSTAT 5V 50-TP 256 10MSOP PDF资料下载
参数资料
| 型号： | AD5274BCPZ-20-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | IC RHEOSTAT 5V 50-TP 256 10MSOP |
| 标准包装： | 1 |
| 接片： | 256 |
| 电阻（欧姆）： | 20k |
| 电路数： | 1 |
| 温度系数： | 标准值 5 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C |
| 电源电压： | 2.7 V ~ 5.5 V，±2.5 V ~ 2.75 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 标准包装 |
| 其它名称： | AD5274BCPZ-20-RL7DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
AD5272/AD5274
Rev. D | Page 23 of 28
50-TP MEMORY WRITE-ACKNOWLEDGE POLLING
After each write operation to the 50-TP registers, an internal
write cycle begins. The I2C interface of the device is disabled.
To determine if the internal write cycle is complete and the
I2C interface is enabled, interface polling can be executed. I2C
interface polling can be conducted by sending a start condition,
followed by the slave address and the write bit. If the I2C interface
responds with an acknowledge (ACK), the write cycle is complete
and the interface is ready to proceed with further operations.
Otherwise, I2C interface polling can be repeated until it completes.
RESET
The AD5272/AD5274 can be reset through software by executing
Command 4 (see Table 12) or through hardware on the low
pulse of the RESET pin. The reset command loads the RDAC
register with the contents of the most recently programmed 50-TP
memory location. The RDAC register loads with midscale if no
50-TP memory location has been previously programmed. Tie
RESET to VDD if the RESET pin is not used.
RESISTOR PERFORMANCE MODE
This mode activates a new, patented 1% end-to-end resistor
tolerance that ensures a ±1% resistor tolerance on each code,
resistor tolerance. The resistor performance mode is activated by
programming Bit C2 of the control register (see Table 14 and
SHUTDOWN MODE
The AD5272/AD5274 can be shut down by executing the software
shutdown command, Command 9 (see Table 12), and setting
the LSB to 1. This feature places the RDAC in a zero-power-
consumption state where Terminal Ax is disconnected from
the wiper terminal. It is possible to execute any command from
Table 12 while the AD5272 or AD5274 is in shutdown mode.
The part can be taken out of shutdown mode by executing
Command 9 and setting the LSB to 0, or by issuing a software
or hardware reset.
RDAC ARCHITECTURE
To achieve optimum performance, Analog Devices has patented the
RDAC segmentation architecture for all the digital potentiometers.
In particular, the AD5272/AD5274 employ a three-stage
segmentation approach, as shown in Figure 46. The AD5272/
AD5274 wiper switch is designed with the transmission gate
CMOS topology.
A
W
10-/8-BIT
ADDRESS
DECODER
RL
RM
RW
SW
RW
08076-
008
Figure 46. Simplified RDAC Circuit
PROGRAMMING THE VARIABLE RESISTOR
Rheostat Operation—1% Resistor Tolerance
The nominal resistance between Terminal W and Terminal A, RWA,
is available in 20 k, 50 k, and 100 k, and 1024-/256-tap points
accessed by the wiper terminal. The 10-/8-bit data in the RDAC
latch is decoded to select one of the 1024 or 256 possible wiper
settings. The AD5272/ AD5274 contain an internal ±1% resistor
tolerance calibration feature which can be disabled or enabled,
enabled by default, or by programming Bit C2 of the control
register (see Table 15). The digitally programmed output resis-
tance between the W terminal and the A terminal, RWA, is
calibrated to give a maximum of ±1% absolute resistance error
over both the full supply and temperature ranges. As a result,
the general equations for determining the digitally programmed
output resistance between the W terminal and A terminal are as
follows:
For the AD5272
WA
R
D
R
×
=
1024
)
(
(1)
For the AD5274
WA
R
D
R
×
=
256
)
(
(2)
where:
D is the decimal equivalent of the binary code loaded in the
10-/8-bit RDAC register.
RWA is the end-to-end resistance.
In the zero-scale condition, a finite total wiper resistance of
120 is present. Regardless of which setting the part is oper-
ating in, take care to limit the current between the A terminal
to B terminal, W terminal to A terminal, and W terminal to
B terminal, to the maximum continuous current of ±3 mA, or
the pulse current specified in Table 8. Otherwise, degradation or
possible destruction of the internal switch contact can occur.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-26J-MY-F2 | CONVERTER MOD DC/DC 36V 50W |
| VE-BNF-IU-F1 | CONVERTER MOD DC/DC 72V 200W |
| VI-2WM-MW | CONVERTER MOD DC/DC 10V 100W |
| VE-26J-MY-F1 | CONVERTER MOD DC/DC 36V 50W |
| VI-2WL-MX-B1 | CONVERTER MOD DC/DC 28V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5274BRMZ-100 | 功能描述:IC RHEOSTAT 5V 50TP 256 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5274BRMZ-100-RL7 | 功能描述:IC RHEOSTAT 5V 50-TP 256 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD5274BRMZ-20 | 功能描述:IC DGTL POT 20K 256POS 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5274BRMZ-20 | 制造商:Analog Devices 功能描述:Digital Potentiometer IC |
| AD5274BRMZ-20-RL7 | 功能描述:IC DGTL POT 20K 256POS 10MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。