–3–
REV. 0
AD53500
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD53500 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
Parameter
Min
Typ
Max
Units
Test Conditions
DYNAMIC PERFORMANCE, INHIBIT
Delay Time, Active to Inhibit
2
10
ns
Measured at 50%, V
H
= +2 V,
V
L
= –2 V, 50
Terminated to Ground
Measured at 50%, V
H
= +2 V,
V
L
= –2 V, 50
Terminated to Ground
V
H
= 0 V, V
L
= 0 V
V
OUT
= –2 V to +6 V
Driver Inhibited
V
S
= V
S
±
3%
Delay Time, Inhibit to Active
2
10
ns
I/O Spike
Output Leakage
Output Capacitance
PSRR, Drive Mode
<200
mV, p-p
μ
A
pF
dB
–1.0
+1.0
18
35
POWER SUPPLIES
Total Supply Range
Positive Supply
Negative Supply
Positive Supply Current
Negative Supply Current
Total Power Dissipation
Temperature Sensor Gain Factor
16
+10
–6
85
88
1.37
1.0
V
V
V
mA
mA
W
μ
A/K
95
98
1.54
R
LOAD
= 10 k
, V
SOURCE
= +10 V
NOTES
Connecting or shorting the decoupling capacitors to ground will result in the destruction of the device.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS
1
Power Supply Voltage
+V
S
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +11 V
–V
S
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –7 V
+V
S
to –V
S
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +18 V
Inputs
DATA,
DATA
, INH,
INH
. . . . . . . . . . . . . . . . +5 V, –3 V
DATA to
DATA
, INH to
INH
V
H
, V
L
to GND . . . . . . . . . . . . . . . . . . . . . . . . . +7 V, –3 V
V
H
to V
L
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +10 V, 0 V
Outputs
V
OUT
Short Circuit Duration to Ground . . . . . . .Indefinite
2
V
OUT
Range in Inhibit Mode . . . . . . . . . . . . . See Figure 1
V
HDCPL
. . . . . . . . Do Not Connect Except for Cap to V
CC3
V
LDCPL
. . . . . . . . . Do Not Connect Except for Cap to V
EE3
THERM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +V
S
, 0 V
Environmental
Operating Temperature (Junction) . . . . . . . . . . . . . .+175
°
C
Storage Temperature . . . . . . . . . . . . . . . . –65
°
C to +150
°
C
Lead Temperature (Soldering, 10 sec)
4
. . . . . . . . . .+260
°
C
. . . . . . . . . . . . . . . .
±
3 V
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Absolute maximum limits apply
individually, not in combination. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
2
Output
short circuit protection is guaranteed as long as proper heat sinking is
employed to ensure compliance with the operating temperature limits.
3
The V
and V
capacitors may be replaced by a low value resistor for higher
dc-current drive capability.
4
To ensure lead coplanarity (
±
0.002 inches) and solderability, handling with bare
hands should be avoided and the device should be stored in environments at 24
°
C
±
5
°
C (75
°
F
±
10
°
F) with relative humidity not to exceed 65%.
WARNING!
ESD SENSITIVE DEVICE
1
2
3
4
5
–1
1
–1
–2
2
3
4
5
6
V
H
, V
L
V
OUT
V
OUT
= (MIN) = –3V
FIGURE 1 SHOWS THE MAXIMUM ALLOWABLE LIMITS FOR V
AS A FUNCTION
OF V
AND V
WHEN THE DRIVER IS OPERATING IN INHIBIT MODE. THE
LIMITS, AS STATED BEFORE, ARE MAXIMUM RATINGS ONLY, AND SHOULD NOT
BE USED AS THE PART'S NORMAL OPERATING RANGE. THIS RANGE APPLIES
ONLY TO SUPPLIES OF +V
= +10V AND –V
S
= –6V AND SHOULD BE DERATED
PROPORTIONALLY FOR LOWER SUPPLIES.
V
HIGH
/ V
LOW
V
OUT
= (MAX) = +7V
–2
6
–3
7
Figure 1. Absolute Maximum Ratings for V
OUT