- 您现在的位置：买卖IC网 > PDF目录373878 > AD5382BST-5 (ANALOG DEVICES INC) 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC PDF资料下载
参数资料
| 型号： | AD5382BST-5 |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | DAC |
| 英文描述： | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
| 中文描述： | PARALLEL, WORD INPUT LOADING, 8 us SETTLING TIME, 14-BIT DAC, PQFP100 |
| 封装： | 14 X 14 MM, MS-026BED, LQFP-100 |
| 文件页数： | 34/40页 |
| 文件大小： | 616K |
| 代理商： | AD5382BST-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页第39页第40页
AD5382
AD5382 MONITOR FUNCTION
The AD5382 contains a channel monitor function that consists
of a multiplexer addressed via the interface, allowing any chan-
nel output to be routed to this pin for monitoring using an
external ADC. The channel monitor function must be enabled
in the control register before any channels are routed to
MON_OUT. Table 18 contains the decoding information
required to route any channel to MON_OUT. External signals
within the AD5382’s absolute max input range can be connected
to the MON_IN pins and monitored at MON_OUT. Selecting
Channel Address 63 three-states MON_OUT. Figure 41 shows a
typical monitoring circuit implemented using a 12-bit SAR
ADC in a 6-lead SOT-23 package. The controller output port
selects the channel to be monitored, and the input port reads
the converted data from the ADC.
Rev. 0 | Page 34 of 40
TOGGLE MODE FUNCTION
The toggle mode function allows an output signal to be gener-
ated using the LDAC control signal that switches between two
DAC data registers. This function is configured using the SFR
control register as follows. A write with REG1 = REG0 = 0 and
A4–A0 = 01100 specifies a control register write. The toggle
mode function is enabled in groups of eight channels using bits
CR5 to CR2 in the control register. See the AD5382 control
register description. Figure 42 shows a block diagram of toggle
mode implementation. Each of the 32 DAC channels on the
AD5382 contain an A and B data register. Note that the B
registers can only be loaded when toggle mode is enabled. The
sequence of events when configuring the AD5382 for toggle
mode is
1.
Enable toggle mode for the required channels via the
control register.
2.
Load data to A registers.
3.
Load data to B registers.
4.
Apply LDAC.
The LDAC is used to switch between the A and B registers in
determining the analog output. The first LDAC configures the
output to reflect the data in the A registers. This mode offers
significant advantages if the user wants to generate a square
wave at the output of all 32 channels, as might be required to
drive a liquid crystal based variable optical attenuator. In this
case, the user writes to the control register and enables the
toggle function by setting CR5 to CR2 = 1, thus enabling the
four groups of eight for toggle mode operation. The user must
then load data to all 32 A and B registers. Toggling LDAC will
set the output values to reflect the data in the A and B registers.
The frequency of the LDAC determines the frequency of the
square wave output.
Toggle mode is disabled via the control register. The first LDAC
following the disabling of the toggle mode will update the
outputs with the data contained in the A registers.
AD7476
V
IN
GND
SDATA
CS
SCLK
AVCC
MON_OUT
AGND
DIN
SYNC
SCLK
DAC_GND SIGNAL_GND
VOUT0
VOUT31
AVCC
AD5382
OUTPUT PORT
INPUT PORT
CONTROLLER
0
AD780/
ADR431
REFOUT/REFIN
MON_IN1
MON_IN2
AVCC
Figure 41. Typical Channel Monitoring Circuit
相关PDF资料 |
PDF描述 |
|---|---|
| AD5382BST-5-REEL | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
| AD5383BST-3 | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
| AD5383BST-5 | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
| AD5383 | 32-Channel, 3 V/5 V, Single-Supply, 12-Bit, Voltage Output DAC |
| AD5383BST-3-REEL | 32-Channel, 3 V/5 V, Single-Supply, 12-Bit, Voltage Output DAC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5382BST-5-REEL | 制造商:Analog Devices 功能描述:DAC 32-CH Resistor-String 14-bit 100-Pin LQFP T/R |
| AD5382BSTZ-3 | 功能描述:IC DAC 14BIT 32CHAN 3V 100LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD5382BSTZ-5 | 功能描述:IC DAC 14BIT 32CH 5V 100-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD5383BST | 制造商:Analog Devices 功能描述:- Bulk |
| AD5383BST-3 | 制造商:Rochester Electronics LLC 功能描述:32/40-CHANNEL 3V/5V SINGLE SUPPLY 12/14-BIT VOUT DAC - Bulk 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。