- 您现在的位置：买卖IC网 > PDF目录8718 > AD5433YRU-REEL (Analog Devices Inc)IC DAC 10BIT MULTIPLYING 20TSSOP PDF资料下载
参数资料
| 型号： | AD5433YRU-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/29页 |
| 文件大小： | 0K |
| 描述： | IC DAC 10BIT MULTIPLYING 20TSSOP |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 标准包装： | 2,500 |
| 设置时间： | 35ns |
| 位数： | 10 |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 25µW |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 2 电流，单极；2 电流，双极 |
| 采样率（每秒）： | 20.4M |
| 配用： | EVAL-AD5433EBZ-ND - BOARD EVAL FOR AD5433 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
AD5424/AD5433/AD5445
Data Sheet
Rev. D | Page 20 of 28
SINGLE-SUPPLY APPLICATIONS
Current Mode Operation
The current mode circuit in Figure 51 shows a typical circuit for
operation with a single 2.5 V to 5 V supply. IOUT2 and therefore
IOUT1 is biased positive by the amount applied to VBIAS. In this
configuration, the output voltage is given by
VOUT = [D × (RFB/RDAC) × (VBIAS VIN)] + VBIAS
or 0 to 4095 (AD5445), the output voltage varies from
VOUT = VBIAS to VOUT = 2VBIAS VIN
VBIAS should be a low impedance source capable of sinking and
sourcing all possible variations in current at the IOUT2 terminal.
03160-051
ADDITIONAL PINS OMITTED FOR CLARITY
C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
IF A1 IS A HIGH SPEED AMPLIFIER.
NOTES:
1.
2.
VDD
VIN
VREF
GND
DAC
C1
A1
RFB
IOUT1
IOUT2
VBIAS
VOUT
Figure 51. Single-Supply Current Mode Operation
It is important to note that VIN is limited to low voltages because
the switches in the DAC ladder no longer have the same source-
drain drive voltage. As a result, there on resistance differs and
the linearity of the DAC degrades.
Voltage Switching Mode of Operation
Figure 52 shows these DACs operating in the voltage-switching
mode. The reference voltage, VIN, is applied to the IOUT1 pin,
IOUT2 is connected to AGND, and the output voltage is available
at the VREF terminal. In this configuration, a positive reference
voltage results in a positive output voltage, making single-supply
operation possible. The output from the DAC is a voltage at a
constant impedance (the DAC ladder resistance), thus an op
amp is necessary to buffer the output voltage. The reference
input no longer sees a constant input impedance, but one that
varies with code. Therefore, the voltage input should be driven
from a low impedance source.
03160-052
VIN
VDD
VREF
VOUT
GND
DAC
RFB
IOUT1
IOUT2
R1
A1
R2
ADDITIONAL PINS OMITTED FOR CLARITY
C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
IF A1 IS A HIGH SPEED AMPLIFIER.
NOTES:
1.
2.
Figure 52. Single-Supply Voltage-Switching Mode Operation
It is important to note that VIN is limited to low voltages because
the switches in the DAC ladder no longer have the same source-
drain drive voltage. As a result, there on resistance differs, which
degrades the linearity of the DAC. See Figure 18 to Figure 23. Also,
VIN must not go negative by more than 0.3 V; otherwise, an internal
diode turns on, exceeding the maximum ratings of the device.
In this type of application, the full range of multiplying capability
of the DAC is lost.
POSITIVE OUTPUT VOLTAGE
Note that the output voltage polarity is opposite to the VREF
polarity for dc reference voltages. To achieve a positive voltage
output, an applied negative reference to the input of the DAC is
preferred over the output inversion through an inverting amplifier
because of the resistor tolerance errors. To generate a negative
reference, the reference can be level-shifted by an op amp such
that the VOUT and GND pins of the reference become the virtual
ground and –2.5 V respectively, as shown in Figure 53.
VDD
RFB
IOUT1
IOUT2
C1
VOUT = 0V TO +2.5V
GND
VDD = 5V
VREF
NOTES:
1ADDITIONAL PINS OMITTED FOR CLARITY.
2C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED,
IF A1 IS A HIGH SPEED AMPLIFIER.
ADR03
VOUT
VIN
GND
–5V
+5V
–2.5V
03160-053
Figure 53. Positive Voltage Output with Minimum of Components
相关PDF资料 |
PDF描述 |
|---|---|
| SL23EP08SC-1HT | IC BUFFER 220MHZ 8CH 3.3V 16SOIC |
| LTC2606IDD-1#PBF | IC DAC 16BIT I2C V-OUT 10-DFN |
| LTC2606IDD#PBF | IC DAC 16BIT I2C V-OUT 10-DFN |
| V24A5H400BG | CONVERTER MOD DC/DC 5V 400W |
| VE-J6M-MZ-F3 | CONVERTER MOD DC/DC 10V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5433YRU-REEL7 | 制造商:Analog Devices 功能描述:DAC 1-CH R-2R 10-bit 20-Pin TSSOP T/R 制造商:Analog Devices 功能描述:DAC 1CH R-2R 10-BIT 20TSSOP - Tape and Reel |
| AD5433YRUZ | 功能描述:IC DAC 10BIT MULTIPLYING 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:1 系列:- 设置时间:4.5µs 位数:12 数据接口:串行，SPI? 转换器数目:1 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOICN 包装:剪切带 (CT) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:* 其它名称:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD5433YRUZ | 制造商:Analog Devices 功能描述:10BIT DAC PARALLEL I/F SMD 5433 |
| AD5433YRUZ-REEL | 功能描述:IC DAC 10BIT MULTIPLYING 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源 功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-DFN-EP（4x3） 包装:管件 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD5433YRUZ-REEL7 | 功能描述:IC DAC 10BIT MULTIPLYING 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源 功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-DFN-EP（4x3） 包装:管件 输出数目和类型:8 电压，单极 采样率（每秒）:* |
发布紧急采购，3分钟左右您将得到回复。