- 您现在的位置：买卖IC网 > PDF目录8718 > AD5433YRU-REEL (Analog Devices Inc)IC DAC 10BIT MULTIPLYING 20TSSOP PDF资料下载
参数资料
| 型号： | AD5433YRU-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 15/29页 |
| 文件大小： | 0K |
| 描述： | IC DAC 10BIT MULTIPLYING 20TSSOP |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 标准包装： | 2,500 |
| 设置时间： | 35ns |
| 位数： | 10 |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 25µW |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 2 电流，单极；2 电流，双极 |
| 采样率（每秒）： | 20.4M |
| 配用： | EVAL-AD5433EBZ-ND - BOARD EVAL FOR AD5433 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Data Sheet
AD5424/AD5433/AD5445
Rev. D | Page 21 of 28
ADDING GAIN
In applications where the output voltage is required to be
greater than VIN, gain can be added with an additional external
amplifier or it can be achieved in a single stage. It is important
to consider the effect of the temperature coefficients of the thin
film resistors of the DAC. Simply placing a resistor in series with
the RFB resistor causes mismatches in the temperature coefficients
and results in larger gain temperature coefficient errors. Instead,
the circuit shown in Figure 54 is a recommended method of
increasing the gain of the circuit. R1, R2, and R3 should have
similar temperature coefficients, but they need not match
the temperature coefficients of the DAC. This approach is
recommended in circuits where gains greater than 1 are
required.
03160-
054
8-/10-/12-BIT
DAC
GND
VDD
RFB
VDD
VOUT
VREF
VIN
ADDITIONAL PINS OMITTED FOR CLARITY
C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE
REQUIRED IF A1 IS A HIGH SPEED AMPLIFIER.
NOTES:
1.
2.
C1
R1
IOUT1
IOUT2
R1 =
GAIN =
R2 + R3
R2
R3
R2
R2R3
R2 + R3
Figure 54. Increasing the Gain of the Current Output DAC
DACS USED AS A DIVIDER OR PROGRAMMABLE
GAIN ELEMENT
Current steering DACs are very flexible and lend themselves to
many different applications. If this type of DAC is connected as
the feedback element of an op amp and RFB is used as the input
resistor, as shown in Figure 55, then the output voltage is
inversely proportional to the digital input fraction, D.
For D = 1 – 2–n the output voltage is
VOUT = –VIN/D = –VIN/(1 2–n)
As D is reduced, the output voltage increases. For small values
of D, it is important to ensure that the amplifier does not saturate
and that the required accuracy is met.
For example, in the circuit shown in Figure 55, an 8-bit DAC
driven with the binary code 0x10 (00010000), that is, 16 decimal,
should cause the output voltage to be 16 × VIN. However, if the
DAC has a linearity specification of ±0.5 LSB, then D can in fact
have a weight anywhere in the range 15.5/256 to 16.5/256 so
that the possible output voltage falls in the range 15.5 VIN to
16.5 VIN—an error of 3% even though the DAC itself has a
maximum error of 0.2%.
03160-055
GND
RFB
VDD
VOUT
VREF
VIN
NOTE:
ADDITIONAL PINS OMITTED FOR CLARITY
IOUT1
IOUT2
Figure 55. Current-Steering DAC Used as a Divider or
Programmable Gain Element
DAC leakage current is also a potential error source in divider
circuits. The leakage current must be counterbalanced by an
opposite current supplied from the op amp through the DAC.
Since only a fraction, D, of the current into the VREF terminal is
routed to the IOUT1 terminal, the output voltage has to change
as follows:
Output Error Voltage due to DAC Leakage = (Leakage × R)/D
where R is the DAC resistance at the VREF terminal.
For a DAC leakage current of 10 nA, R = 10 kΩ, and a gain
(that is, 1/D) of 16, the error voltage is 1.6 mV.
相关PDF资料 |
PDF描述 |
|---|---|
| SL23EP08SC-1HT | IC BUFFER 220MHZ 8CH 3.3V 16SOIC |
| LTC2606IDD-1#PBF | IC DAC 16BIT I2C V-OUT 10-DFN |
| LTC2606IDD#PBF | IC DAC 16BIT I2C V-OUT 10-DFN |
| V24A5H400BG | CONVERTER MOD DC/DC 5V 400W |
| VE-J6M-MZ-F3 | CONVERTER MOD DC/DC 10V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5433YRU-REEL7 | 制造商:Analog Devices 功能描述:DAC 1-CH R-2R 10-bit 20-Pin TSSOP T/R 制造商:Analog Devices 功能描述:DAC 1CH R-2R 10-BIT 20TSSOP - Tape and Reel |
| AD5433YRUZ | 功能描述:IC DAC 10BIT MULTIPLYING 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:1 系列:- 设置时间:4.5µs 位数:12 数据接口:串行，SPI? 转换器数目:1 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOICN 包装:剪切带 (CT) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:* 其它名称:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD5433YRUZ | 制造商:Analog Devices 功能描述:10BIT DAC PARALLEL I/F SMD 5433 |
| AD5433YRUZ-REEL | 功能描述:IC DAC 10BIT MULTIPLYING 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源 功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-DFN-EP（4x3） 包装:管件 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD5433YRUZ-REEL7 | 功能描述:IC DAC 10BIT MULTIPLYING 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源 功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-DFN-EP（4x3） 包装:管件 输出数目和类型:8 电压，单极 采样率（每秒）:* |
发布紧急采购，3分钟左右您将得到回复。