- 您现在的位置：买卖IC网 > PDF目录10909 > AD5700ACPZ-RL7 (Analog Devices Inc)IC HART MODEM LP 24LFCSP PDF资料下载
参数资料
| 型号： | AD5700ACPZ-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC HART MODEM LP 24LFCSP |
| 标准包装： | 1,500 |
| 系列： | * |
Data Sheet
AD5700/AD5700-1
Rev. F | Page 17 of 24
APPLICATIONS INFORMATION
SUPPLY DECOUPLING
It is recommended to decouple the VCC and IOVCC supplies with
10 μF in parallel with 0.1 μF capacitors to ground. For many
applications, 1 μF in parallel with 0.1 μF ceramic capacitors to
ground should be sufficient. The REG_CAP voltage of 1.8 V is
used to supply the AD5700/AD5700-1 internal circuitry and is
derived from the VCC supply using a high efficiency clocking
LDO. Decouple this REG_CAP supply with a 1 μF ceramic
capacitor to ground. It is also required to decouple the REF pin
with a 1 μF ceramic capacitor to ground. Place decoupling
capacitors as close to the relevant pins as possible.
For loop-powered applications, it is recommended to connect a
resistance in series with the VCC supply to minimize the effect of
any noise, which may, depending on the system configuration, be
introduced onto the loop as a result of current draw variations
resistance has proven most effective. However, depending on the
application conditions, alternative values may also be acceptable
(see R1 in Figure 31).
TRANSIENT VOLTAGE PROTECTION
Many industrial control applications have requirements for
HART-enabled current input and output modules. Figure 28
shows an example of a HART-enabled current input module
that contains transient voltage protection circuitry, which is
very important in harsh industrial control environments.
The module is powered from a 24 V field supply, and the 250 Ω
load is within the low impedance module itself. This configuration
is in contrast to Figure 29, which demonstrates a secondary HART
device, in which the load is outside of the module. For transient
voltage protection, a 10 V unidirectional (for protection against
positive high voltage transients) transient voltage suppressor (TVS)
is placed at the connection point of the current input module.
The TVS component that is used in a given application circuit
must have power ratings that are appropriate to the individual
system. When choosing the TVS, low leakage current is also an
important specification for maintaining the accuracy of the analog
current input. In the event of a transient spike, the 22 Ω series
resistor acts as a current limiting resistor for the FSK output pin.
The FSK input pin is inherently protected by the 150 kΩ resistor,
which forms part of the recommended external filter circuitry
at the FSK input. The voltage divider, made up of both a 75 kΩ
resistor and a 22 kΩ resistor, is used to maintain a 0.75 V dc bias
at the field side of the FSK output switch.
Figure 28. Current Input Module, HART Circuit
Figure 29. Secondary HART Device
10
43
5-
0
31
HART_OUT
ADC_IP
AGND
TXD
RXD
RTS
CD
VCC
AD5700/
AD5700-1
ADC
REF
10nF
3.3V
75k
22k
2.2F
22
6.8nF
3.3V
1.2M
300pF
150k
150pF
10F
10V
400W
MICRO-
CONTROLLER
VLOOP
24V
FI
E
LD
INS
T
RUM
E
NT
20k
250
1F
1
0435-
03
0
HART_OUT
ADC_IP
AGND
TXD
RXD
RTS
CD
AD5700/
AD5700-1
REF
10nF
3.3V
75k
22k
2.2F
50V
4.7
0.5W
6.8nF
50V
3.3V
1.2M
300pF
150k
150pF
39V
1500W
20
10V
400W
HOST
1F
VCC
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2NT-IX-F2 | CONVERTER MOD DC/DC 6.5V 75W |
| VE-26V-CV | CONVERTER MOD DC/DC 5.8V 150W |
| VE-2NR-IX-F4 | CONVERTER MOD DC/DC 7.5V 75W |
| VE-26M-CV | CONVERTER MOD DC/DC 10V 150W |
| VE-2NR-IX-F3 | CONVERTER MOD DC/DC 7.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5700BCPZ-R5 | 功能描述:IC INTERFACE MODEM RoHS:是 类别:集成电路 (IC) >> 接口 - 调制解调器 - IC 和模块 系列:* 标准包装:25 系列:- 数据格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 电源电压:3.3V 安装类型:- 封装/外壳:- 供应商设备封装:- 包装:托盘 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名称:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
| AD5700BCPZ-RL7 | 功能描述:IC HART MODEM LP 24LFCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 调制解调器 - IC 和模块 系列:* 标准包装:25 系列:- 数据格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 电源电压:3.3V 安装类型:- 封装/外壳:- 供应商设备封装:- 包装:托盘 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名称:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
| AD5700CPZ-R5 | 制造商:Analog Devices 功能描述:LOW POWER HART MODEM - Tape and Reel |
| AD57050/+ | 制造商:Analog Devices 功能描述: |
| AD570-703D | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。