参数资料
| 型号： | AD5760BCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/28页 |
| 文件大小： | 0K |
| 描述： | IC DAC VOLT OUT 16BIT 24LFCSP |
| 标准包装： | 1 |
| 设置时间： | 2.5µs |
| 位数： | 16 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 24-LFCSP-VQ EP（4x5） |
| 包装： | 托盘 |
| 输出数目和类型： | 1 电压，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD5760
Data Sheet
Rev. D | Page 18 of 28
TERMINOLOGY
Relative Accuracy
Relative accuracy, or integral nonlinearity (INL), is a measure of
the maximum deviation, in LSB, from a straight line passing
through the endpoints of the DAC transfer function. A typical
INL error vs. code plot is shown in Figure 5.
Differential Nonlinearity (DNL)
Differential nonlinearity is the difference between the measured
change and the ideal 1 LSB change between any two adjacent
codes. A specified differential nonlinearity of ±1 LSB maximum
ensures monotonicity. This DAC is guaranteed monotonic. A
typical DNL error vs. code plot is shown in Figure 9.
Linearity Error Long-Term Stability
Linearity error long-term stability is a measure of the stability of
the linearity of the DAC over a long period of time. It is specified
in LSB for a time period of 500 hours and 1000 hours at an
elevated ambient temperature.
Zero-Scale Error
Zero-scale error is a measure of the output error when zero-scale
code (0x00000) is loaded to the DAC register. Ideally, the output
voltage should be VREFN. Zero-scale error is expressed in LSBs.
Zero-Scale Error Temperature Coefficient
Zero-scale error temperature coefficient is a measure of the
change in zero-scale error with a change in temperature. It is
expressed in ppm FSR/°C.
Full-Scale Error
Full-scale error is a measure of the output error when full-scale
code (0x0FFFF) is loaded to the DAC register. Ideally, the
output voltage should be VREFP 1 LSB. Full-scale error is
expressed in LSBs.
Full-Scale Error Temperature Coefficient
Full-scale error temperature coefficient is a measure of the
change in full-scale error with a change in temperature. It is
expressed in ppm FSR/°C.
Gain Error
Gain error is a measure of the span error of the DAC. It is the
deviation in slope of the DAC transfer characteristic from the
ideal, expressed in ppm of the full-scale range.
Gain Error Temperature Coefficient
Gain error temperature coefficient is a measure of the change in
gain error with a change in temperature. It is expressed in ppm
FSR/°C.
Midscale Error
Midscale error is a measure of the output error when midscale
code (0x08000) is loaded to the DAC register. Ideally, the output
voltage should be (VREFP – VREFN)/2 +VREFN. Midscale error is
expressed in LSBs.
Output Voltage Settling Time
Output voltage settling time is the amount of time it takes for
the output voltage to settle to a specified level for a specified
change in voltage. For fast settling applications, a high speed
buffer amplifier is required to buffer the load from the 3.4 k
output impedance of the AD5760, in which case, it is the
amplifier that determines the settling time.
Digital-to-Analog Glitch Impulse
Digital-to-analog glitch impulse is the impulse injected into the
analog output when the input code in the DAC register changes
state. It is specified as the area of the glitch in nV-sec and is
measured when the digital input code is changed by 1 LSB at
the major carry transition (see Figure 48).
Output Enabled Glitch Impulse
Output enabled glitch impulse is the impulse injected into the
analog output when the clamp to ground on the DAC output is
removed. It is specified as the area of the glitch in nV-sec (see
Digital Feedthrough
Digital feedthrough is a measure of the impulse injected into
the analog output of the DAC from the digital inputs of the
DAC but is measured when the DAC output is not updated. It is
specified in nV-sec and measured with a full-scale code change
on the data bus, that is, from all 0s to all 1s, and vice versa.
Total Harmonic Distortion (THD)
Total harmonic distortion is the ratio of the rms sum of the
harmonics of the DAC output to the fundamental value. Only
the second to fifth harmonics are included.
DC Power Supply Rejection Ratio.
DC power supply rejection ratio is a measure of the rejection of
the output voltage to dc changes in the power supplies applied
to the DAC. It is measured for a given dc change in power
supply voltage and is expressed in V/V.
AC Power Supply Rejection Ratio (AC PSRR)
AC power supply rejection ratio is a measure of the rejection of
the output voltage to ac changes in the power supplies applied
to the DAC. It is measured for a given amplitude and frequency
change in power supply voltage and is expressed in decibels.
相关PDF资料 |
PDF描述 |
|---|---|
| AD5762RCSUZ-REEL7 | IC DAC 16BIT QUAD VOUT 32-TQFP |
| AD5763CSUZ-REEL7 | DAC 16BIT DUAL 5V 2LSB 32-TQFP |
| AD5764CSUZ | IC DAC 16BIT QUAD VOUT 32TQFP |
| AD5764RBSUZ | IC DAC 16BIT QUAD VOUT 32-TQFP |
| AD5781BRUZ-REEL7 | IC DAC 18BIT SRL 20TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5760BCPZ-REEL7 | 功能描述:数模转换器- DAC 16B +/-0.5 LSB INL VOut RoHS:否 制造商:Analog Devices 转换器数量:4 DAC 输出端数量:4 转换速率: 分辨率:12 bit 接口类型:Serial (I2C) 稳定时间: 最大工作温度:+ 105 C 安装风格: 封装 / 箱体:TSSOP 封装:Reel |
| AD5761ACPZ-RL7 | 功能描述:IC DAC 16BIT 1CH 8LSB 16LFCSP 制造商:analog devices inc. 系列:- 零件状态:在售 位数:16 数模转换器数:1 建立时间:12.5μs 输出类型:Voltage - Buffered 差分输出:无 数据接口:SPI 参考类型:外部 电压 - 电源，模拟:4.5 V ~ 30 V， -16.5V 电压 - 电源，数字:1.7 V ~ 5.5 V INL/DNL（LSB）:±8（最大），±1（最大） 架构:R-2R 工作温度:-40°C ~ 125°C 标准包装:1 |
| AD5761ARUZ | 功能描述:16 Bit Digital to Analog Converter 1 16-TSSOP 制造商:analog devices inc. 系列:- 包装:管件 零件状态:有效 位数:16 数模转换器数:1 建立时间:12.5μs 输出类型:Voltage - Buffered 差分输出:无 数据接口:SPI 参考类型:外部 电压 - 电源，模拟:4.5 V ~ 30 V， -16.5V 电压 - 电源，数字:1.7 V ~ 5.5 V INL/DNL（LSB）:±8（最大），±1（最大） 架构:R-2R 工作温度:-40°C ~ 125°C 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商器件封装:16-TSSOP 标准包装:96 |
| AD5761ARUZ-RL7 | 功能描述:16 Bit Digital to Analog Converter 1 16-TSSOP 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:有效 位数:16 数模转换器数:1 建立时间:12.5μs 输出类型:Voltage - Buffered 差分输出:无 数据接口:SPI 参考类型:外部 电压 - 电源，模拟:4.5 V ~ 30 V， -16.5V 电压 - 电源，数字:1.7 V ~ 5.5 V INL/DNL（LSB）:±8（最大），±1（最大） 架构:R-2R 工作温度:-40°C ~ 125°C 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商器件封装:16-TSSOP 标准包装:1,000 |
| AD5761BCPZ-RL7 | 功能描述:16 Bit Digital to Analog Converter 1 16-LFCSP-WQ (3x3) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:有效 位数:16 数模转换器数:1 建立时间:12.5μs 输出类型:Voltage - Buffered 差分输出:无 数据接口:SPI 参考类型:外部 电压 - 电源，模拟:4.5 V ~ 30 V， -16.5V 电压 - 电源，数字:1.7 V ~ 5.5 V INL/DNL（LSB）:±2（最大），±1（最大） 架构:R-2R 工作温度:-40°C ~ 125°C 封装/外壳:16-WFQFN 裸露焊盘，CSP 供应商器件封装:16-LFCSP-WQ（3x3） 标准包装:1,500 |
发布紧急采购，3分钟左右您将得到回复。