参数资料
| 型号： | AD5764CSUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/28页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT QUAD VOUT 32TQFP |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 产品变化通告： | AD5764(R), AD5744R Product Change 04/Sept/2009 |
| 设计资源： | High Accuracy, Bipolar Voltage Output Digital-to-Analog Conversion Using AD5764 (CN0006) |
| 标准包装： | 1 |
| 设置时间： | 8µs |
| 位数： | 16 |
| 数据接口： | 串行 |
| 转换器数目： | 4 |
| 电压电源： | 双 ± |
| 功率耗散（最大）： | 275 mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-TQFP |
| 供应商设备封装： | 32-TQFP（7x7） |
| 包装： | 托盘 |
| 输出数目和类型： | 4 电压，双极 |
| 采样率（每秒）： | 1.26M |
| 产品目录页面： | 784 (CN2011-ZH PDF) |
| 配用： | EVAL-AD5764EBZ-ND - BOARD EVAL FOR AD5764 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD5764
Data Sheet
Rev. F | Page 24 of 28
DESIGN FEATURES
ANALOG OUTPUT CONTROL
In many industrial process control applications, it is vital that
the output voltage be controlled during power-up and during
brownout conditions. When the supply voltages are changing,
the VOUTx pins are clamped to 0 V via a low impedance path.
To prevent the output amp being shorted to 0 V during this time,
Transmission Gate G1 is also opened (see Figure 35). These condi-
tions are maintained until the power supplies stabilize and a
valid word is written to the data register. At this time, G2 opens and
G1 closes. Both transmission gates are also externally controllable
via the reset logic (RSTIN) control input. For instance, if RSTIN
is driven from a battery supervisor chip, the RSTIN input is
driven low to open G1 and close G2 upon power-down or during
a brownout. Conversely, the on-chip voltage detector output
(RSTOUT) is also available to the user to control other parts of
the system. The basic transmission gate functionality is shown
in
.
05
30
3-
0
6
3
G1
G2
RSTOUT
RSTIN
VOUTA
AGNDA
VOLTAGE
MONITOR
AND
CONTROL
Figure 35. Analog Output Control Circuitry
DIGITAL OFFSET AND GAIN CONTROL
The AD5764 incorporates a digital offset adjust function with a
±16 LSB adjust range and 0.125 LSB resolution. The coarse gain
register allows the user to adjust the AD5764 full-scale output
range. The full-scale output can be programmed to achieve full-
scale ranges of ±10 V, ±10.2564 V, and ±10.5263 V. A fine gain
trim is also provided.
PROGRAMMABLE SHORT-CIRCUIT PROTECTION
The short-circuit current of the output amplifiers can be pro-
grammed by inserting an external resistor between the ISCC
pin and PGND. The programmable range for the current is 500 μA
to 10 mA, corresponding to a resistor range of 120 kΩ to 6 kΩ.
The resistor value is calculated as follows:
C
I
R
S
60
=
If the ISCC pin is left unconnected, the short-circuit current
limit defaults to 5 mA. Note that limiting the short-circuit
current to a small value can affect the slew rate of the output
when driving into a capacitive load; therefore, the value of the
programmed short circuit should take into account the size of
the capacitive load being driven.
DIGITAL I/O PORT
The AD5764 contains a 2-bit digital I/O port (D1 and D0).
These bits can be configured as inputs or outputs independently,
and can be driven or have their values read back via the serial
interface. The I/O port signals are referenced to DVCC and DGND.
When configured as outputs, they can be used as control signals
to multiplexers or can be used to control calibration circuitry
elsewhere in the system. When configured as inputs, the logic
signals from limit switches can, for example, be applied to D0
and D1 and can be read back via the digital interface.
LOCAL GROUND OFFSET ADJUST
The AD5764 incorporates a local ground offset adjust feature
that, when enabled in the function register, adjusts the DAC
outputs for voltage differences between the individual DAC ground
pins, AGNDx, and the REFGND pin, ensuring that the DAC
output voltages are always with respect to the local DAC ground
pin. For instance, if Pin AGNDA is at +5 mV with respect to the
REFGND pin and VOUTA is measured with respect to AGNDA,
a 5 mV error results, enabling the local ground offset adjust
feature to adjust VOUTA by +5 mV, eliminating the error.
相关PDF资料 |
PDF描述 |
|---|---|
| AD5764RBSUZ | IC DAC 16BIT QUAD VOUT 32-TQFP |
| AD5781BRUZ-REEL7 | IC DAC 18BIT SRL 20TSSOP |
| AD5790BCPZ | IC DAC VOLT OUT 20BIT 24LFCSP |
| AD5791BRUZ | IC DAC 20BIT SRL 20TSSOP |
| AD5821ABCBZ-REEL | IC DAC 10BIT CURRENTSINK 9WLCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5764CSUZ-REEL7 | 功能描述:IC DAC 16BIT QUAD BIPO 32-TQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD5764R | 制造商:AD 制造商全称:Analog Devices 功能描述:Complete Quad, 16-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC |
| AD5764R_08 | 制造商:AD 制造商全称:Analog Devices 功能描述:Complete Quad, 16-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC |
| AD5764RASUZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Complete Quad, 16-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC |
| AD5764RASUZ-REEL7 | 制造商:AD 制造商全称:Analog Devices 功能描述:Complete Quad, 16-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC |
发布紧急采购，3分钟左右您将得到回复。