- 您现在的位置：买卖IC网 > PDF目录10980 > AD5932YRUZ (Analog Devices Inc)IC PROG WAVEFORM GEN SNGL16TSSOP PDF资料下载
参数资料
| 型号： | AD5932YRUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/28页 |
| 文件大小： | 0K |
| 描述： | IC PROG WAVEFORM GEN SNGL16TSSOP |
| 产品培训模块： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 标准包装： | 96 |
| 分辨率（位）： | 10 b |
| 主 fclk： | 50MHz |
| 调节字宽（位）： | 24 b |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 797 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD5932
Data Sheet
Rev. A | Page 18 of 28
Therefore, in this example, a time interval of 20 ns × 2047 = 40 s
is the maximum, with the minimum being 40 ns. For some
applications, this maximum time of 40 s may be insufficient.
Therefore, to allow for sweeps that need a longer increment
interval, time-base multipliers are provided. D12 and D11 are
dedicated to the time-base multipliers, as shown in the bit map
above. A more detailed table of the multiplier options is given in
Table 9. Time-Base Multiplier Values
D12
D11
Multiplier Value
0
Multiply (1/MCLK) by 1
0
1
Multiply (1/MCLK) by 5
1
0
Multiply (1/MCLK) by 100
1
Multiply (1/MCLK) by 500
If MCLK = 50 MHz and a multiplier of 500 is used, then the
base interval (TBASE) is now (1/(50 MHz) x 500)) = 10 s. Using
a multiplier of 500, the maximum increment interval is 10 s ×
211 1= 20.5 ms. Therefore, the option of time-base multipliers
gives the user enhanced flexibility when programming the
length of the frequency window, because any frequency can be
output for a minimum of 40 ns up to a maximum of 20.5 ms.
The above example shows a fixed number of clock periods.
Note that the same equally applies to fixed numbers of clock
cycles.
Length of Scan Time
The length of time to complete a user-programmed frequency
scan is given by the following equation:
TSCAN = (1 + NINCR) × TBASE
ACTIVATING AND CONTROLLING THE SCAN
After the registers have been programmed, a 0 to 1 transition
on the CTRL pin starts the scan. The scan always starts from
the frequency programmed into the FSTART register. It changes by
the value in the f register and increases by the number of steps
in the NINCR register. However, the time interval of each frequency
can be internally controlled using the tINT register or externally
controlled using the CTRL pin. The available options are
Auto-increment
External increment
Auto-Increment Control
The value in the tINT register is used to control the scan. The
AD5932 outputs each frequency for the length of time pro-
grammed in the TINT register, before moving on to the next
frequency.
To set up the AD5932 to this mode, INT/EXT INCR (Bit D5)
must be set to 0.
External Increment Control
In this case, the time interval, tINT, is set by the pulse rate on the
CTRL pin. The first 0 to 1 transition on the pin starts the scan.
Each subsequent 0 to 1 transition on the CTRL pin increments
the output frequency by the value programmed into the f register.
To set up the AD5932 to this mode, INT/EXT INCR (Bit D5)
must be set to 1.
INTERRUPT Pin
This function is used as an interrupt during a frequency scan.
A low-to-high transition on this pin is sampled by the internal
MCLK, thereby resetting internal state machines, which results
in the output going to midscale.
STANDBY Pin
Sections of the AD5932 that are not in use can be powered
down to minimize power consumption. This is done by using
the STANDBY pin. For optimum power savings, it is recom-
mended to reset the AD5932 before entering standby. Doing so
reduces the power-down current to 20 μA.
When this pin is high, the internal MCLK is disabled, and the
reference, DAC, and regulator are powered down. When in this
state, the DAC output of the AD5932 remains at its present
value, because the NCO is no longer accumulating. When the
device is taken back out of standby mode, the MCLK is re-
activated, and the scan continues. To ensure correct operation
for new data, it is recommended that the device be internally
reset, using a control register write or using the INTERRUPT
pin, and then restarted.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9833BRMZ | IC WAVEFORM GENERTR PROG 10-MSOP |
| VE-B1J-IX-B1 | CONVERTER MOD DC/DC 36V 75W |
| VI-B1J-IX-B1 | CONVERTER MOD DC/DC 36V 75W |
| AD9838BCPZ-RL7 | IC DDS 16MHZ LP 20LFCSP |
| VI-21L-CU-S | CONVERTER MOD DC/DC 28V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5932YRUZ-REEL7 | 功能描述:IC PROG WAVEFORM GENERAT 16TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 直接数字合成 (DDS) 系列:- 产品变化通告:Product Discontinuance 27/Oct/2011 标准包装:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 调节字宽（位）:32 b 电源电压:2.97 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD5933 | 制造商:AD 制造商全称:Analog Devices 功能描述:1 MSPS 12-Bit Impedance Converter, Network Analyzer |
| AD5933BRSZ-U1 | 制造商:Analog Devices 功能描述:CNVRTR NETWORK ANALYZER 16SSOP - Rail/Tube |
| AD5933YRSZ | 功能描述:IC NTWK ANALYZER 12B 1MSP 16SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 直接数字合成 (DDS) 系列:- 产品变化通告:Product Discontinuance 27/Oct/2011 标准包装:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 调节字宽（位）:32 b 电源电压:2.97 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD5933YRSZ | 制造商:Analog Devices 功能描述:IC IMPEDANCE CONV 1MSPS 12BIT 16SSOP |
发布紧急采购，3分钟左右您将得到回复。