- 您现在的位置：买卖IC网 > PDF目录10977 > AD5934YRSZ-REEL7 (Analog Devices Inc)IC CONV 12BIT 250KSPS 16SSOP PDF资料下载
参数资料
| 型号： | AD5934YRSZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/32页 |
| 文件大小： | 0K |
| 描述： | IC CONV 12BIT 250KSPS 16SSOP |
| 产品培训模块： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 标准包装： | 500 |
| 分辨率（位）： | 12 b |
| 主 fclk： | 16.776MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 带卷 (TR) |
| 配用： | EVAL-AD5934EBZ-ND - BOARD EVALUATION FOR AD5934 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Data Sheet
AD5934
Rev. C | Page 17 of 32
GAIN FACTOR TEMPERATURE VARIATION
The typical impedance error variation with temperature is in
the order of 30 ppm/°C. Figure 21 shows an impedance profile
with a variation in temperature for 100 k impedance using a
2-point gain factor calibration.
101.5
98.5
54
66
05325-
087
FREQUENCY (kHz)
IM
PE
DANCE
(k
)
101.0
100.5
100.0
99.5
99.0
56
58
60
62
64
+125°C
+25°C
–40°C
VDD = 3.3V
CALIBRATION FREQUENCY = 60kHz
MEASURED CALIBRATION IMPEDANCE = 100k
Figure 21. Impedance Profile Variation with Temperature Using a
2-Point Gain Factor Calibration
IMPEDANCE ERROR
Refer to Circuit Note CN-0217 on the AD5933 product page,
which highlights a method to improve accuracy. The EVAL-
AD5933EBZ board can be used to evaluate the AD5934
performance.
MEASURING THE PHASE ACROSS AN IMPEDANCE
The AD5934 returns a complex output code made up of a
separate real and imaginary components. The real component is
stored at Register Address 0x94 and Register Address 0x95, and
the imaginary component is stored at Register Address 0x96
and Register Address 0x97 after each sweep measurement. These
correspond to the real and imaginary components of the DFT
and not the resistive and reactive components of the impedance
under test.
For example, it is a common misconception to assume that if a
user was analyzing a series RC circuit that the real value stored
in Register Address 0x94 and Register Address 0x95 and the
imaginary value stored in Register Address 0x96 and Register
Address 0x97 would correspond to the resistance and capacitive
reactance, respectfully. However, this is incorrect because the
magnitude of the impedance (|Z|) can be calculated by calculating
the magnitude of the real and imaginary components of the
DFT given by the following formula:
2
I
R
Magnitude
+
=
After each measurement, multiply it by the calibration term and
invert the product. Therefore, the magnitude of the impedance
is given by the following formula:
Magnitude
Factor
Gain
Impedance
×
=
1
Where the gain factor is given by
Magnitude
Impedance
1
Code
Admittance
Factor
Gain
=
=
The user must calibrate the AD5934 system for a known
impedance range to determine the gain factor before any valid
measurement can take place. Therefore, the user must know
the impedance limits of the complex impedance (ZUNKNOWN) for
the sweep frequency range of interest. The gain factor is simply
determined by placing a known impedance between the input/
output of the AD5934 and measuring the resulting magnitude of
the code. The AD5934 system gain settings need to be chosen to
place the excitation signal in the linear region of the on-board ADC.
Because the AD5934 returns a complex output code made up of
real and imaginary components, the user is also able to calculate
the phase of the response signal through the signal path of the
AD5934. The phase is given by the following formula:
Phase (rads) = tan1(I/R)
(3)
The phase measured by Equation 3 accounts for the phase
shift introduced to the DDS output signal as it passes through the
internal amplifiers on the transmit and receive side of the AD5934,
along with the low-pass filter, and also the impedance connected
between the VOUT and VIN pins of the AD5934.
The parameters of interest for many users are the magnitude of
the impedance (|ZUNKNOWN|) and the impedance phase (Z).The
measurement of the impedance phase (Z) is a 2-step process.
The first step involves calculating the AD5934 system phase.
The AD5934 system phase can be calculated by placing a
resistor across the VOUT and VIN pins of the AD5934 and
calculating the phase (using Equation 3) after each measurement
point in the sweep. By placing a resistor across the VOUT and
VIN pins, there is no additional phase lead or lag introduced to
the AD5934 signal path, and the resulting phase is due entirely
to the internal poles of the AD5934, that is, the system phase.
Once the system phase is calibrated using a resistor, the second
step involves calculating the phase of any unknown impedance
can be calculated by inserting the unknown impedance between
the VIN and VOUT terminals of the AD5934 and recalculating
the new phase (including the phase due to the impedance) using
the same formula. The phase of the unknown impedance (Z)
is given by
Z = (Φunknown system
)
where:
system
is the phase of the system with a calibration resistor
connected between VIN and VOUT.
Φunknown is the phase of the system with the unknown
impedance connected between VIN and VOUT.
Z is the phase due to the impedance, that is, the impedance phase.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B1D-IX-B1 | CONVERTER MOD DC/DC 85V 75W |
| AD9833BRMZ-REEL7 | IC WAVEFORM GEN PROG 10MSOP |
| VE-B1D-IW-B1 | CONVERTER MOD DC/DC 85V 100W |
| MCF51AC256BCFUE | MCU 32BIT 256K FLASH 64-QFP |
| AD9833BRMZ-REEL | IC WAVEFORM GEN PROG 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD594 | 制造商:AD 制造商全称:Analog Devices 功能描述:Monolithic Thermocouple Amplifiers with Cold Junction Compensation |
| AD594A | 制造商:AD 制造商全称:Analog Devices 功能描述:Monolithic Thermocouple Amplifiers with Cold Junction Compensation |
| AD594AD | 制造商:Analog Devices 功能描述:Temp Sensor Analog 14-Pin TO-116 制造商:Rochester Electronics LLC 功能描述:THERMOCOUPLER AMPLIFIER - Bulk 制造商:Analog Devices 功能描述:Special Function IC Package/Case:TO-116 |
| AD594AD/+ | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD594ADZ | 功能描述:IC THERMOCOUPLE INSTR AMP 14CDIP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:3,000 系列:- 功能:温度开关 传感器类型:内部 感应温度:85°C 分界点 精确度:±6°C（最小值） 拓扑:ADC（三角积分型），比较器，寄存器库 输出类型:开路漏极 输出警报:是 输出风扇:是 电源电压:2.7 V ~ 5.5 V 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:ADT6501SRJZP085RL7-ND |
发布紧急采购，3分钟左右您将得到回复。