参数资料
| 型号： | AD606JN |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC AMP LOG LP 1.2MA 16DIP |
| 标准包装： | 1 |
| 放大器类型： | 对数 |
| 电路数： | 1 |
| 输出类型： | 差分 |
| 电流 - 输入偏压： | 4µA |
| 电流 - 电源： | 13mA |
| 电流 - 输出 / 通道： | 1.2mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 16-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 16-PDIP |
| 包装： | 管件 |
AD606
REV. B
–7–
For operation above 10 MHz, it is not necessary to add the
external capacitors CF1, CF2, and CZ, although an improve-
ment in low frequency noise can be achieved by so doing (see
APPLICATIONS). Note that the offset control loop does not
materially affect the low-frequency cutoff at high input levels,
when the offset voltage is swamped by the signal.
Power-Up Interface
The AD606 features a power-saving mode, controlled by the
logic level at Pin 14 (PRUP). When powered down, the quies-
cent current is typically 65
A, or about 325 W. A CMOS
logical HIGH applied to PRUP activates both internal refer-
ences, and the system becomes fully functional within about
3.5
s. When this input is a CMOS logical LOW, the system
shuts down to the quiescent level within about 5
s.
The power-up time is somewhat dependent on the signal level
and can be degraded by mismatch of the input coupling capaci-
tors. The explanation is as follows. When the AD606 makes the
transition from powered-down to fully active, the dc bias voltage
at the input nodes INHI and INLO (about +2.5 V) inevitably
changes slightly, as base current in the input transistors flows in
the bias resistors. In fact, first-order correction for this is in-
cluded in the specially designed offset buffer amplifier, but even
a few millivolts of change at these inputs represents a significant
equivalent “dBm” level.
Now, if the coupling capacitors do not match exactly, some
fractional part of this residual voltage step becomes coupled into
the amplifier. For example, if there is a 10% capacitor mis-
match, and INHI and INLO jump 20 mV at power-up, there is
a 2 mV pulse input to the system, which may cause the offset
control loop to ring. Note that 2 mV is roughly 40 times greater
than the amplitude of a sinusoidal input at –75 dBm. As long as
the ringing persists, the AD606 will be “blind” to the actual
input, and VLOG will show major disturbances.
The solution to this problem is first, to ensure that the loop
filter does not ring, and second, to use well-matched capacitors
at the signal input. Use the component values suggested above
to minimize ringing.
APPLICATIONS
Note that the AD606 has more than 70 MHz of input band-
width and 90 dB of gain! Careful shielding is needed to realize
its full dynamic range, since nearly all application sites will be
pervaded by many kinds of interference, radio and TV stations,
etc., all of which the AD606 faithfully hears. In bench evalua-
tion, we recommend placing all of the components in a shielded
box and using feedthrough decoupling networks for the supply
voltage. In many applications, the AD606’s low power drain
allows the use of a 6 V battery inside the box.
Basic RSSI Application
Figure 6 shows the basic RSSI (Receiver Signal Strength Indica-
tor) application circuit, including the calibration adjustments,
either or both of which may be omitted in noncritical applica-
tions. This circuit may be used “as is” in such measurement
applications as the log/IF strip in a spectrum or network ana-
lyzer or, with the addition of an FM or QPSK demodulator fed
by the limiter outputs, as an IF strip in such communications
applications as a GSM digital mobile radio or FM receiver.
The slope adjustment works in this way: the buffer amplifier
(which forms part of a Sallen-Key two-pole filter, see Figure 2)
has a dc gain of plus two, and the resistance from BFIN (buffer
in) to OPCM (output common) is nominally 9.375 k
. This
resistance is driven from the logarithmic detector sections with a
current scaled 2
A/dB, generating 18.75 mV/dB at BFIN,
hence 37.5 mV/dB at VLOG Now, a resistor (R4 in Figure 6)
connected directly between BFIN and VLOG would form a
controlled positive-feedback network with the internal 9.375 k
resistor which would raise the gain, and thus increase the slope
voltage, while the same external resistor connected between
BFIN and ground would form a shunt across the internal resis-
tor and reduce the slope voltage. By connecting R4 to a potenti-
ometer R2 across the output, the slope may be adjusted either
way; the value for R4 shown in Figure 6 provides approximately
± 10% range, with essentially no effect on the slope at the
midposition.
The intercept may be adjusted by adding a small current into
BFIN via R1 and R3. The AD606 is designed to have the nomi-
nal intercept value of –88 dBm when R1 is centered using this
network, which provides a range of
±5 dB.
51.1
100pF
RF INPUT
NC
R5
200
LIMITER OUTPUT
LOGARITHMIC
OUTPUT
R3
412k
R4
174k
R1
200k
INTERCEPT
ADJUSTMENT
5dB
R2
50k
SLOPE
ADJUSTMENT
10%
+5V
INHI
COMM
PRUP
VPOS
FIL1
FIL2
LADJ
LMHI
INLO
COMM
ISUM
ILOG
BFIN
VLOG
OPCM
LMLO
AD606
NC
0.1 F
NC = NO CONNECT
Figure 6. Basic Application Circuit Showing Optional Slope and Intercept Adjustments
相关PDF资料 |
PDF描述 |
|---|---|
| TV02W101B-HF | TVS 200W 100V BIDIRECT SOD-123 |
| TV02W101B-G | TVS 200W 100V BIDIRECT SOD-123 |
| TLC2272CPSRG4 | IC OPAMP GP R-R 2.25MHZ 8SOIC |
| TV02W100B-HF | TVS 200W 10V BIDIRECT SOD-123 |
| 86584-214HLF | BERGSTIK II DR STRAIGHT RET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD606JNZ | 功能描述:IC AMP LOG LP 1.2MA 16DIP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| AD606JNZ | 制造商:Analog Devices 功能描述:IC AMP ((NS)) |
| AD606JR | 功能描述:IC AMP LOG LP 1.2MA 16SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:TS1854A View All Specifications 标准包装:50 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.25 V/µs 增益带宽积:630kHz -3db带宽:- 电流 - 输入偏压:16nA 电压 - 输入偏移:1000µV 电流 - 电源:162µA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):1.8 V ~ 6 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 |
| AD606JR-REEL | 制造商:Analog Devices 功能描述:SP Amp LOG Amp Single 5.5V 16-Pin SOIC N T/R 制造商:Analog Devices 功能描述:SP AMP LOG AMP SGL 5.5V 16SOIC N - Tape and Reel |
| AD606JR-REEL7 | 功能描述:IC AMP LOG LP 1.2MA 16SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:3.5 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:30pA 电压 - 输入偏移:2000µV 电流 - 电源:200µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。