- 您现在的位置：买卖IC网 > PDF目录9508 > AD7142ACPZ-1REEL (Analog Devices Inc)IC CAP-TO-DGTL CONV PROG 32LFCSP PDF资料下载
参数资料
| 型号： | AD7142ACPZ-1REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 26/73页 |
| 文件大小： | 0K |
| 描述： | IC CAP-TO-DGTL CONV PROG 32LFCSP |
| 标准包装： | 1 |
| 类型： | 电容数字转换器 |
| 分辨率（位）： | 16 b |
| 采样率（每秒）： | 250k |
| 数据接口： | 串行 |
| 电压电源： | 单电源 |
| 电源电压： | 2.6 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-VQ |
| 包装： | 标准包装 |
| 产品目录页面： | 781 (CN2011-ZH PDF) |
| 其它名称： | AD7142ACPZ-1REELDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页
AD7142
Rev. A | Page 31 of 72
SERIAL INTERFACE
The AD7142 is available with an SPI serial interface. The
AD7142-1 is available with an I2C-compatible interface. Both
parts are the same, with the exception of the serial interface.
SPI INTERFACE
The AD7142 has a 4-wire serial peripheral interface (SPI). The
SPI has a data input pin (SDI) for inputting data to the device, a
data output pin (SDO) for reading data back from the device,
and a data clock pin (SCLK) for clocking data into and out of
the device. A chip select pin (CS) enables or disables the serial
interface. CS is required for correct operation of the SPI
interface. Data is clocked out of the AD7142 on the negative
edge of SCLK, and data is clocked into the device on the
positive edge of SCLK.
SPI Command Word
All data transactions on the SPI bus begin with the master
taking CS from high to low and sending out the command
word. This indicates to the AD7142 whether the transaction is a
read or a write, and gives the address of the register from which
to begin the data transfer. The following bit map shows the SPI
command word.
MSB
LSB
15
14
13
12
11
10
9:0
1
0
R/W
Register address
Bits[15:11] of the command word must be set to 11100 to
successfully begin a bus transaction.
Bit 10 is the read/write bit; 1 indicates a read, and 0 indicates a
write.
Bits[9:0] contain the target register address. When reading or
writing to more than one register, this address indicates the
address of the first register to be written to or read from.
Writing Data
Data is written to the AD7142 in 16-bit words. The first word
written to the device is the command word, with the read/write
bit set to 0. The master then supplies the 16-bit input data-word
on the SDI line. The AD7142 clocks the data into the register
addressed in the command word. If there is more than one
word of data to be clocked in, the AD7142 automatically incre-
ments the address pointer, and clocks the next data-word into
the next register.
The AD7142 continues to clock in data on the SDI line until
either the master finishes the write transition by pulling CS
high, or the address pointer reaches its maximum value. The
AD7142 address pointer does not wrap around. When it
reaches its maximum value, any data provided by the master on
the SDI line is ignored by the AD7142.
NOTES
1. SDI BITS ARE LATCHED ON SCLK RISING EDGES. SCLK CAN IDLE HIGH OR LOW BETWEEN WRITE OPERATIONS.
2. ALL 32 BITS MUST BE WRITTEN: 16 BITS FOR CONTROL WORD AND 16 BITS FOR DATA.
3. 16-BIT COMMAND WORD SETTINGS FOR SERIAL WRITE OPERATION:
CW[15:11] = 11100 (ENABLE WORD)
CW[10] = 0 (R/W)
CW[9:0] = [AD9, AD8, AD7, AD6, AD5, AD4, AD3, AD2, AD1, AD0] (10-BIT MSB JUSTIFIED REGISTER ADDRESS)
CW
11
CW
10
CW
13
CW
12
SDI
CW
15
CW
14
CW
9
CW
7
CW
6
CW
5
CW
4
CW
3
CW
2
CW
1
CW
0
D2
D1
D0
CW
8
t1
t4
16-BIT COMMAND WORD
16-BIT DATA
5
32
6
7
8
9
10
11
12
13
14
15
16
30
31
t8
t5
SCLK
1234
D15
D14
D13
17
18
19
CS
ENABLE WORD
R/W
REGISTER ADDRESS
t2
t3
057
02-
033
Figure 46. Single Register Write SPI Timing
相关PDF资料 |
PDF描述 |
|---|---|
| V110A8M200BL2 | CONVERTER MOD DC/DC 8V 200W |
| CS3106A-24-67P | CONN PLUG 19POS STRAIGHT W/PINS |
| V110A8M200BL | CONVERTER MOD DC/DC 8V 200W |
| MS27497T18F35SC | CONN RCPT 66POS WALL MNT W/SCKT |
| V110A8M200B3 | CONVERTER MOD DC/DC 8V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7142ACPZ-1REEL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Programmable Controller for Capacitance Touch Sensors |
| AD7142ACPZ-500RL7 | 功能描述:IC CAP-TO-DGTL CONV PROG 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| AD7142ACPZ-500RL71 | 制造商:AD 制造商全称:Analog Devices 功能描述:Programmable Controller for Capacitance Touch Sensors |
| AD7142ACPZ-REEL | 功能描述:IC CAP-TO-DGTL CONV PROG 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| AD7142ACPZ-REEL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Programmable Controller for Capacitance Touch Sensors |
发布紧急采购，3分钟左右您将得到回复。