参数资料
| 型号： | AD7191BRUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/21页 |
| 文件大小： | 0K |
| 描述： | IC ADC 2CH 24B SD 24TSSOP |
| 产品培训模块： | Weigh Scale Introduction |
| 设计资源： | Precision Weigh Scale Design Using AD7191 with Internal PGA (CN0118) |
| 标准包装： | 62 |
| 位数： | 24 |
| 采样率（每秒）： | 120 |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 管件 |
| 输入数目和类型： | 2 个差分，双极 |
| 产品目录页面： | 777 (CN2011-ZH PDF) |
AD7191
Rev. A | Page 18 of 20
In systems where the AGND and DGND pins are connected
somewhere else in the system(that is, at the system power
supply), they should not be connected again at the AD7191
because a ground loop results. In these situations, it is
recommended that the AD7191 AGND and DGND pins be tied
to the AGND plane. In any layout, it is important that the user
keep in mind the flow of currents in the system, ensuring that
the return paths for all currents are as close as possible to the
paths the currents took to reach their destinations. Avoid
forcing digital currents to flow through the AGND sections of
the layout.
Avoid running digital lines under the device because these
couple noise onto the die. The analog ground plane should be
allowed to run under the AD7191 to prevent noise coupling.
The power supply lines to the AD7191 should use as wide a
trace as possible to provide low impedance paths and reduce
the effects of glitches on the power supply line. Fast switching
signals like clocks should be shielded with digital ground to
avoid radiating noise to other sections of the board, and clock
signals should never be run near the analog inputs. Avoid
crossover of digital and analog signals. Traces on opposite
sides of the board should run at right angles to each other.
This reduces the effects of feedthrough through the board.
A microstrip technique is by far the best but is not always
possible with a double-sided board. In this technique, the
component side of the board is dedicated to ground planes,
and signals are placed on the solder side.
Good decoupling is important when using high resolution
ADCs. All analog supplies should be decoupled with 10 μF
tantalum capacitors in parallel with 0.1 μF capacitors to AGND.
To achieve the best from these decoupling components, they
have to be placed as close as possible to the device, ideally right
up against the device. All logic chips should be decoupled with
0.1 μF ceramic capacitors to DGND. In systems where a
common supply voltage is used to drive both the AVDD and
DVDD of the AD7191, it is recommended that the system AVDD
supply be used. This supply should have the recommended
analog supply decoupling capacitors between the AVDD pin of
the AD7191 and AGND, and the recommended digital supply
decoupling capacitor between the DVDD pin of the AD7191 and
DGND.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7192BRUZ | IC ADC 24BIT 2CH W/PGA 24-TSSOP |
| AD7193BCPZ | IC ADC 24BIT SPI 4.8KHZ 32LFCSP |
| AD7194BCPZ | IC ADC 24BIT SPI 4.8K 32-LFCSP |
| AD7195BCPZ-RL7 | IC AFE 24BIT 4.8K 32LFSP |
| AD7225BQ | IC DAC 8BIT QUAD W/AMP 24-CDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7191BRUZ | 制造商:Analog Devices 功能描述:IC ADC 24BIT 120SPS TSSOP-24 |
| AD7191BRUZ-REEL | 功能描述:IC ADC 24BIT 2CH LN SD 24TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7191KSTZ | 制造商:Analog Devices 功能描述: |
| AD7191S/0B | 制造商:Sony Nec Optiarc America 功能描述:DOUBLE DUAL INTERNAL DVDRW SATA BEZEL 20X/18X12XRAM - Bulk |
| AD7192 | 制造商:AD 制造商全称:Analog Devices 功能描述:4.8 kHz, Ultralow Noise, 24-Bit Sigma-Delta ADC with PGA |
发布紧急采购，3分钟左右您将得到回复。