参数资料
| 型号： | AD7192BRUZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 28/41页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT 2CH W/PGA 24-TSSOP |
| 产品培训模块： | Weigh Scale Introduction |
| 设计资源： | Precision Weigh Scale Design Using AD7192 with Internal PGA (CN0119) |
| 标准包装： | 62 |
| 位数： | 24 |
| 采样率（每秒）： | 4.8k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 管件 |
| 输入数目和类型： | 2 个差分，单极；2 个差分，双极；4 个伪差分，单极；4 个伪差分，双极 |
| 产品目录页面： | 777 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
AD7192
Rev. A | Page 33 of 40
clock source is used, the clock source must be connected to the
MCLK2 pin, and the MCLK1 pin can be left floating.
The internal clock can also be made available at the MCLK2
pin. This is useful when several ADCs are used in an application
and the devices must be synchronized. The internal clock from
one device can be used as the clock source for all ADCs in the
system. Using a common clock, the devices can be synchro-
nized by applying a common reset to all devices, or the SYNC
pin can be pulsed.
BURNOUT CURRENTS
The AD7192 contains two 500 nA constant current generators,
one sourcing current from AVDD to AIN(+) and one sinking
current from AIN() to AGND, where AIN(+) is the positive
analog input terminal and AIN() is the negative analog input
terminal in differential mode and AINCOM in pseudodiffer-
ential mode. The currents are switched to the selected analog
input pair. Both currents are either on or off, depending on the
burnout current enable (BURN) bit in the configuration
register.
These currents can be used to verify that an external transducer
is still operational before attempting to take measurements on
that channel. After the burnout currents are turned on, they
flow in the external transducer circuit, and a measurement of
the input voltage on the analog input channel can be taken. It
takes some time for the burnout currents to detect an open
circuit condition because the currents must charge any external
capacitors.
There are several reasons that a fault condition is detected. The
front-end sensor may be open circuit. It could also mean that
the front-end sensor is overloaded or the reference may be
absent and the NOREF bit in the status register is set, thus
clamping the data to all 1s.
The user must check these three cases before making a judgment.
If the voltage measured is 0 V, it may indicate that the
transducer has short circuited. The current sources work over
the normal absolute input voltage range specifications when the
analog inputs are buffered and chop is disabled.
REFERENCE
The ADC has a fully differential input capability for the
reference channel. In addition, the user has the option of
selecting one of two external reference options (REFIN1(x) or
REFIN2(x)). The reference source for the AD7192 is selected
using the REFSEL bit in the configuration register. The
REFIN2(x) pins are dual purpose: they can function as two
general-purpose output pins or as reference pins. When the
REFSEL bit is set to 1, these pins automatically function as
reference pins.
The common-mode range for these differential inputs is from
AGND to AVDD. The reference input is unbuffered; therefore,
excessive R-C source impedances introduce gain errors. The
reference voltage REFIN (REFINx(+) REFINx()) is AVDD
nominal, but the AD7192 is functional with reference voltages
from 1 V to AVDD. In applications where the excitation (voltage
or current) for the transducer on the analog input also drives
the reference voltage for the part, the effect of the low frequency
noise in the excitation source is removed because the application is
ratiometric. If the AD7192 is used in a nonratiometric applica-
tion, a low noise reference should be used.
Recommended 2.5 V reference voltage sources for the AD7192
references. These references have low output impedances and
are, therefore, tolerant to having decoupling capacitors on
REFINx(+) without introducing gain errors in the system.
Deriving the reference input voltage across an external resistor
means that the reference input sees a significant external source
impedance. External decoupling on the REFINx pins is not
recommended in this type of circuit configuration.
REFERENCE DETECT
The AD7192 includes on-chip circuitry to detect whether the
part has a valid reference for conversions or calibrations. This
feature is enabled when the REFDET bit in the configuration
register is set to 1. If the voltage between the selected REFINx(+)
and REFINx() pins is between 0.3 V and 0.6 V, the AD7192
detects that it no longer has a valid reference. In this case, the
NOREF bit of the status register is set to 1. If the AD7192 is
performing normal conversions and the NOREF bit becomes
active, the conversion result is all 1s.
Therefore, it is not necessary to continuously monitor the status
of the NOREF bit when performing conversions. It is only
necessary to verify its status if the conversion result read from
the ADC data register is all 1s. If the AD7192 is performing
either an offset or full-scale calibration and the NOREF bit
becomes active, the updating of the respective calibration
registers is inhibited to avoid loading incorrect coefficients to
these registers, and the ERR bit in the status register is set. If the
user is concerned about verifying that a valid reference is in
place every time a calibration is performed, the status of the
ERR bit should be checked at the end of the calibration cycle.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7193BCPZ | IC ADC 24BIT SPI 4.8KHZ 32LFCSP |
| AD7194BCPZ | IC ADC 24BIT SPI 4.8K 32-LFCSP |
| AD7195BCPZ-RL7 | IC AFE 24BIT 4.8K 32LFSP |
| AD7225BQ | IC DAC 8BIT QUAD W/AMP 24-CDIP |
| AD7226BQ | IC DAC 8BIT QUAD W/AMP 20-CDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7192BRUZ-REEL | 功能描述:IC ADC 24BIT 2CH SD 24-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7193 | 制造商:AD 制造商全称:Analog Devices 功能描述:4-Channel, 4.8 kHz, Ultralow Noise, 24-Bit Sigma-Delta ADC with PGA |
| AD7193BCPZ | 功能描述:IC ADC 24BIT SPI 4.8KHZ 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7193BCPZ-RL | 功能描述:IC ADC 24BIT SPI 4.8KHZ 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7193BCPZ-RL7 | 功能描述:IC ADC 24BIT SPI 4.8KHZ 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。