- 您现在的位置：买卖IC网 > PDF目录1980 > AD7298BCPZ-RL7 (Analog Devices Inc)IC ADC 10BIT SPI/SRL 8CH 20LFCSP PDF资料下载
参数资料
| 型号： | AD7298BCPZ-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/25页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT SPI/SRL 8CH 20LFCSP |
| 标准包装： | 1 |
| 位数： | 12 |
| 采样率（每秒）： | 1M |
| 数据接口： | DSP，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 22.7mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 20-LFCSP-WQ（4x4） |
| 包装： | 标准包装 |
| 输入数目和类型： | 8 个单端，单极 |
| 其它名称： | AD7298BCPZ-RL7DKR |
AD7298
Rev. B | Page 18 of 24
CS
SCLK
DOUT
DIN
112
16
1
16
1
16
CONVERSION RESULT
FOR CHANNEL 0
CONVERSION RESULT
FOR CHANNEL 1
INVALID DATA
NO WRITE TO THE
CONTROL REGISTER
NO WRITE TO THE
CONTROL REGISTER
DATA WRITTEN TO CONTROL
REGISTER CH 0, CH 1, AND CH 2
SELECTED: REPEAT = 1
CS
SCLK
DOUT
DIN
116
CONVERSION RESULT
FOR CHANNEL 0
CONVERSION RESULT
FOR CHANNEL 2
NO WRITE TO THE
CONTROL REGISTER
NO WRITE TO THE
CONTROL REGISTER
NO WRITE TO THE
CONTROL REGISTER
0
875
4-
0
1
Figure 27. Configuring a Conversion and Read in Repeat Mode
REPEAT OPERATION
The REPEAT bit in the control register allows the user to select
a sequence of channels on which the AD7298 continuously
converts. When the REPEAT bit is set in the control register,
the AD7298 continuously cycles through the selected channels
in ascending order, beginning with the lowest channel and
converting all channels selected in the control register. On
completion of the sequence, the AD7298 returns to the first
selected channel in the control register and recommences the
sequence.
The conversion sequence of the selected channels in the repeat
mode of operation continues until such time as the control
register of the AD7298 is reprogrammed. If the TSENSE bit is
selected in the control register, then the temperature conversion
will be available for conversion after the last analog input
channel in the sequence has been converted. It is not necessary
to write to the control register once a repeat operation is
initiated unless a change in the AD7298 configuration is
required. The WRITE bit must be set to zero or the DIN line
tied low to ensure that the control register is not accidentally
overwritten, or the automatic conversion sequence interrupted.
A write to the control register during the repeat mode of
operation resets the cycle even if the selected channels are
unchanged. Thus, the next conversion by the AD7298 after
a write operation will be the first selected channel in the
sequence.
To select a sequence of channels, the associated channel bit
must be set to a logic high state (1) for each analog input whose
conversion is required. For example, if the REPEAT bit = 1,
then CH0, CH1, and CH2 = 1. The VIN0 analog input is
converted on the first CS falling edge following the write to
the control register, the VIN1 channel is converted on the
subsequent CS falling edge, and the VIN0 conversion result is
available for reading. The third CS falling edge following the
write operation initiates a conversion on VIN2 and has the VIN1
result available for reading. The AD7298 operates with one
cycle latency, thus the conversion result corresponding to each
conversion is available one serial read cycle after the cycle in
which the conversion is initiated.
This mode of operation simplifies the operation of the device by
allowing consecutive channels to be converted without having
to reprogram the control register or write to the part on each
serial transfer. Figure 27 illustrates how to set up the AD7298
to continuously convert on a particular sequence of channels.
To exit the repeat mode of operation and revert back to the
traditional mode of operation of a multichannel ADC, ensure
that the REPEAT bit = 0 on the next serial write.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7302BRUZ-REEL7 | IC DAC 8BIT DUAL R-R 20-TSSOP |
| AD7303BRM | IC DAC 8BIT DUAL R-R 8-MSOP |
| AD7305BRU | IC DAC 8BIT QUAD R-R 20-TSSOP |
| AD7321BRUZ-REEL7 | IC ADC 12BIT+ SAR 2CHAN 14TSSOP |
| AD7322BRUZ-REEL7 | IC ADC 12BIT+ SAR 2CHAN 14TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD73 | 制造商:Distributed By MCM 功能描述:REFRIGERATR DOOR GASKET DIRECT |
| AD7302 | 制造商:AD 制造商全称:Analog Devices 功能描述:2.7 V to 5.5 V, Parallel Input Dual Voltage Output 8-Bit DAC |
| AD7302BN | 功能描述:IC DAC 8BIT DUAL R-R 20-DIP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
| AD7302BNZ | 功能描述:IC DAC 8BIT DUAL R-R 20-DIP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 设置时间:4µs 位数:12 数据接口:串行 转换器数目:2 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-uMAX 包装:管件 输出数目和类型:2 电压，单极 采样率（每秒）:* 产品目录页面:1398 (CN2011-ZH PDF) |
| AD7302BR | 功能描述:IC DAC 8BIT DUAL 2.7V 20-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
发布紧急采购，3分钟左右您将得到回复。