- 您现在的位置：买卖IC网 > PDF目录10745 > AD73360LARZ-REEL7 (Analog Devices Inc)IC PROCESSOR FRONTEND 6CH 28SOIC PDF资料下载
参数资料
| 型号： | AD73360LARZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/35页 |
| 文件大小： | 0K |
| 描述： | IC PROCESSOR FRONTEND 6CH 28SOIC |
| 标准包装： | 400 |
| 位数： | 16 |
| 通道数： | 6 |
| 功率（瓦特）： | 80mW |
| 电压 - 电源，模拟： | 3V |
| 电压 - 电源，数字： | 3V |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
REV. A
AD73360
–18–
Control Register C
CRC:0
Global Power-Up. Writing a 1 to this bit will cause all six channels of the AD73360 to power-up regardless of the
status of the Power Control Bits in CRD-CRF. If less than six channels are required, this bit should be set to 0 and
the Power Control Bits of the relevant channels should be set to 1.
CRC:1–4
Reserved. These bits are reserved and should be programmed to 0 to ensure correct operation.
CRC:5
Power-Up Reference. This bit controls the state of the on-chip reference. A 1 in this bit will power up the refer-
ence. A 0 in this bit will power-down the reference. Note that the reference is automatically powered up if any
channel is enabled.
CRC:6
Reference Output. When this bit is set to 1, the REFOUT pin is enabled.
CRC:7
5 V Enable. When this bit is set to 1, the 5 V operating mode is enabled.
Control Register D
CRD:0–2
Input Gain Selection. These bits select the input gain for ADC1. See Table IV.
CRD:3
Power Control for ADC1. A 1 in this bit powers up ADC1.
CRD:4–6
Input Gain Selection. These bits select the input gain for ADC2. See Table IV.
CRD:7
Power Control for ADC2. A 1 in this bit powers up ADC2.
Control Register E
CRE:0-2
Input Gain Selection. These bits select the input gain for ADC3. See Table IV.
CRE:3
Power Control for ADC3. A 1 in this bit powers up ADC3.
CRE:4–6
Input Gain Selection. These bits select the input gain for ADC4. See Table IV.
CRE:7
Power Control for ADC4. A 1 in this bit powers up ADC4.
Control Register F
CRF:0–2
Input Gain Selection. These bits select the input gain for ADC5. See Table IV.
CRF:3
Power Control for ADC5. A 1 in this bit powers up ADC5.
CRF:4–6
Input Gain Selection. These bits select the input gain for ADC6. See Table IV.
CRF:7
Power Control for ADC6. A 1 in this bit powers up ADC6.
Control Register G
CRG:0–5
Channel Select. These bits are used in association with CRG:6 and CRG:7. If the Reset Analog Modulator bit
(CRG:6) is 1, then a 1 in a Channel Select bit location will reset the Analog Modulator for that channel. If the
Single-Ended Enable Mode bit (CRG:7) is 1, then a 1 in a Channel Select bit location will put that channel into
Single-Ended Mode. If any channel has its Channel Select bit set to 0, the channel will be set for Differentially-
Ended Mode and will not have its analog modulator reset regardless of the state of CRG:6 and CRG:7.
CRG:6
Reset Analog Modulator. Setting this bit to a 1 will reset the Analog Modulators for any channel whose Channel
Select bit (CRG:0–5) is set to 1. This bit should be set to 0 for normal operation.
CRG:7
Single-Ended Enable Mode. Setting this bit to a 1 will enable Single-Ended Mode on any channel whose Channel
Select bit (CRG:0–5) is set to 1. Setting this bit to 0 will select Differentially-Ended Input Mode for all channels.
Control Register H
CRH:0–5
Invert Select. These bits are used in association with CRH:7. If the Enable Invert Channel Mode bit (CRH:7) is 1,
then a 1 in a Channel Select bit location will put that channel into Inverted Mode. If any channel has its Channel
Select bit set to 0, the channel will not be inverted regardless of the state CRH:7.
CRH:6
Test Mode Enable. This bit should be set to 0 to ensure normal operation.
CRH:7
Enable Invert Channel Mode. Setting this bit to a 1 will enable invert any channel whose Channel Select bit
(CRH:0–5) is set to 1. Setting this bit to 0 will select Noninverted (Normal) Mode for all channels.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX965EUA+ | IC COMPARATOR R-R 8-UMAX |
| MAX966ESA+ | IC COMPARATOR R-R 8-SOIC |
| VE-JN4-MY-F1 | CONVERTER MOD DC/DC 48V 50W |
| MAX965ESA+ | IC COMPARATOR R-R 8-SOIC |
| VE-JN3-MY-F4 | CONVERTER MOD DC/DC 24V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7339 | 制造商:AD 制造商全称:Analog Devices 功能描述:5 V Integrated High Speed ADC/Quad DAC System |
| AD7339BS | 制造商:Analog Devices 功能描述:Data Acquisition System Single ADC Quad DAC 8-Bit 52-Pin MQFP |
| AD7339BS-REEL | 制造商:Analog Devices 功能描述:Data Acquisition System Single ADC Quad DAC 8-Bit 52-Pin MQFP T/R |
| AD7339BSZ-REEL | 功能描述:IC ADC/QUAD DAC 5V W/REF 52-MQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| AD734 | 制造商:AD 制造商全称:Analog Devices 功能描述:10 MHz, 4-Quadrant Multiplier/Divider |
发布紧急采购，3分钟左右您将得到回复。