- 您现在的位置：买卖IC网 > PDF目录10135 > AD7623ASTZRL (Analog Devices Inc)IC ADC 16BIT 1.33MSPS DFF 48LQFP PDF资料下载
参数资料
| 型号： | AD7623ASTZRL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 20/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 1.33MSPS DFF 48LQFP |
| 标准包装： | 2,000 |
| 系列： | PulSAR® |
| 位数： | 16 |
| 采样率（每秒）： | 1.33M |
| 数据接口： | 串行，并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 55mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个差分，双极 |
| 配用： | EVAL-AD7623CBZ-ND - BOARD EVALUATION FOR AD7623 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7623
Rev. 0 | Page 27 of 28
APPLICATION
LAYOUT
While the AD7623 has very good immunity to noise on the
power supplies, exercise care with the grounding layout. To
facilitate the use of ground planes that can be easily separated,
design the printed circuit board that houses the AD7623 so that
the analog and digital sections are separated and confined to
certain areas of the board. Digital and analog ground planes
should be joined in only one place, preferably underneath the
AD7623, or as close as possible to the AD7623. If the AD7623 is
in a system where multiple devices require analog-to-digital
ground connections, the connections should still be made at
one point only, a star ground point, established as close as
possible to the AD7623.
To prevent coupling noise onto the die, avoid radiating noise,
and to reduce feedthrough:
Do not run digital lines under the device.
Do run the analog ground plane under the AD7623.
Do shield fast switching signals, like CNVST or clocks, with
digital ground to avoid radiating noise to other sections of
the board, and never run them near analog signal paths.
Avoid crossover of digital and analog signals.
Run traces on different but close layers of the board, at right
angles to each other, to reduce the effect of feedthrough
through the board.
The power supply lines to the AD7623 should use as large a
trace as possible to provide low impedance paths and reduce the
effect of glitches on the power supply lines. Good decoupling is
also important to lower the impedance of the supplies presented
to the AD7623, and to reduce the magnitude of the supply
spikes. Decoupling ceramic capacitors, typically 100 nF, should
be placed on each of the power supplies pins, AVDD, DVDD,
and OVDD. The capacitors should be placed close to, and
ideally right up against, these pins and their corresponding
ground pins. Additionally, low ESR 10 μF capacitors should be
located in the vicinity of the ADC to further reduce low
frequency ripple.
The DVDD supply of the AD7623 can be either a separate
supply or come from the analog supply, AVDD, or from the
digital interface supply, OVDD. When the system digital supply
is noisy, or fast switching digital signals are present, and no
separate supply is available, it is recommended to connect the
DVDD digital supply to the analog supply AVDD through an
RC filter, and to connect the system supply to the interface
digital supply OVDD and the remaining digital circuitry. Refer
to Figure 23 for an example of this configuration. When DVDD
is powered from the system supply, it is useful to insert a bead
to further reduce high frequency spikes.
The AD7623 has four different ground pins: REFGND, AGND,
DGND, and OGND. REFGND senses the reference voltage and,
because it carries pulsed currents, should be a low impedance
return to the reference. AGND is the ground to which most
internal ADC analog signals are referenced; it must be
connected with the least resistance to the analog ground plane.
DGND must be tied to the analog or digital ground plane
depending on the configuration. OGND is connected to the
digital system ground.
The layout of the decoupling of the reference voltage is
important. To minimize parasitic inductances, place the
decoupling capacitor close to the ADC and connect it with
short, thick traces.
EVALUATING THE AD7623 PERFORMANCE
A recommended layout for the AD7623 is outlined in the
documentation of the EVAL-AD7623CB evaluation board
for the AD7623. The evaluation board package includes a fully
assembled and tested evaluation board, documentation, and
software for controlling the board from a PC via the
EVAL-CONTROL BRD3.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7703BRZ-REEL | IC ADC 20BIT LC2MOS MONO 20SOIC |
| MS27467T17B26SC | CONN PLUG 26POS STRAIGHT W/SCKT |
| AD7703BR-REEL | IC ADC 20BIT LC2MOS MONO 20-SOIC |
| MS27467T17B26SB | CONN PLUG 26POS STRAIGHT W/SCKT |
| AD8392AAREZ-R7 | IC LINE DRVR ADSL/ADSL 28-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7623BD | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Data Acquisition |
| AD7625 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 6MSPS PulSAR Differential ADC |
| AD7625BCPZ | 功能描述:IC ADC 16BIT 6MSPS SAR 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7625BCPZRL7 | 功能描述:IC ADC 16BIT 6MSPS SAR 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7626 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 10 MSPS, PulSAR Differential ADC |
发布紧急采购，3分钟左右您将得到回复。