- 您现在的位置：买卖IC网 > PDF目录10532 > AD7656YSTZ-1 (Analog Devices Inc)IC ADC 16BIT 6CH 250KSPS 64LQFP PDF资料下载
参数资料
| 型号： | AD7656YSTZ-1 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 5/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 6CH 250KSPS 64LQFP |
| 标准包装： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 250k |
| 数据接口： | 串行，并联 |
| 转换器数目： | 6 |
| 功率耗散（最大）： | 143mW |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
| 输入数目和类型： | 6 个单端，双极 |
| 配用： | EVAL-AD7656-1EDZ-ND - BOARD EVAL CONTROL AD7656-1 EVAL-AD7656-1CBZ-ND - BOARD EVAL FOR AD7656-1 EVAL-AD7656CBZ-ND - BOARD EVAL FOR AD7656 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Data Sheet
AD7656-1/AD7657-1/AD7658-1
Rev. D | Page 13 of 32
Pin No.
Mnemonic
Description
7
DB8/DOUT A
Data Bit 8/Serial Data Output A. When SER/PAR SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR SEL = 1 and SEL A = 1, this pin functions as DOUT A and outputs serial
conversion data.
6
DB9/DOUT B
Data Bit 9/Serial Data Output B. When SER/PAR SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR SEL = 1 and SEL B = 1, this pin functions as DOUT B and outputs serial
conversion data. This configures the serial interface to have two DOUT output lines.
5
DB10/DOUT C
Data Bit 10/Serial Data Output C. When SER/PAR SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR SEL = 1 and SEL C = 1, this pin functions as DOUT C and outputs serial
conversion data. This configures the serial interface to have three DOUT output lines.
4
DB11
Data Bit 11/Digital Ground. When SER/PAR SEL = 0, this pin acts as a three-state parallel digital
output pin. When SER/PAR SEL = 1, tie this pin to DGND.
2, 3, 64
DB13, DB12, DB15
Data Bit 12, Data Bit 13, Data Bit 15. When SER/PAR SEL = 0, these pins act as three-state parallel
digital input/output pins. When CS and RD are low, these pins are used to output the conversion
result. When CS and WR are low, these pins are used to write to the control register. When SER/PAR
SEL = 1, tie these pins to DGND. For the AD7657-1, DB15 contains a leading 0. For the AD7658-1,
DB15, DB13, and DB12 contain leading 0s.
1
DB14/REFBUFEN/DIS
Data Bit 14/Reference Buffer Enable and Disable. When SER/PAR SEL = 0, this pin acts as a three-
state digital input/output pin. For the AD7657-1 and AD7658-1, DB14 contains a leading 0. When
SER/PAR SEL = 1, this pin can be used to enable or disable the internal reference buffers.
28
RESET
Reset Input. When set to logic high, this pin resets the AD7656-1/AD7657-1/AD7658-1. In software
mode, the current conversion is aborted and the internal register is set to all 0s. In hardware mode, the
AD7656-1/AD7657-1/AD7658-1 are configured depending on the logic levels on the hardware select
pins. In all modes, the parts should receive a RESET pulse after power-up. The RESET high pulse should
be typically 100 ns wide. The CONVST pin may be held high during the RESET pulse. However, if the
CONVST pin is held low during the RESET pulse, then after the RESET pulse, the AD7656-1/AD7657-1
/AD7658-1 need to receive a complete CONVST pulse to initiate the first conversion; this should consist
of a high-to-low CONVST edge followed by a low-to-high CONVST edge. In hardware mode, the user
can initiate a RESET pulse between conversion cycles, that is, a 100 ns RESET pulse can be applied to
the device after BUSY has transitioned from high to low and the data has been read. The RESET can
then be issued prior to the next complete CONVST pulse. Ensure that in such a case, RESET has
returned to logic low prior to the next complete CONVST pulse.
27
RANGE
Analog Input Range Selection. Logic input. The logic level on this pin determines the input range of
the analog input channels. When this pin is Logic 1 at the falling edge of BUSY, the range for the
next conversion is ±2 × VREF. When this pin is Logic 0 at the falling edge of BUSY, the range for the
next conversion is ±4 × VREF. In hardware select mode, the RANGE pin is checked on the falling edge
of BUSY. In software mode (H/S SEL = 1), the RANGE pin can be tied to DGND, and the input range is
determined by the RNGA, RNGB, and RNGC bits in the control register.
31
VDD
Positive Power Supply Voltage. This is the positive supply voltage for the analog input section.
30
VSS
Negative Power Supply Voltage. This is the negative supply voltage for the analog input section.
24
STBY
Standby Mode Input. This pin is used to put all six on-chip ADCs into standby mode. The STBY pin is
high for normal operation and low for standby operation.
62
H/S SEL
Hardware/Software Select Input. Logic input. When H/S SEL = 0, the AD7656-1/AD7657-1/AD7658-1
operate in hardware select mode, and the ADC pairs to be simultaneously sampled are selected
by the CONVST pins. When H/S SEL = 1, the ADC pairs to be sampled simultaneously are selected by
writing to the control register. When the serial interface is selected, CONVST A is used to initiate
conversions on the selected ADC pairs.
29
W/B
Word/Byte Input. When this pin is logic low, data can be transferred to and from the AD7656-1/
AD7657-1/AD7658-1 using the parallel data lines DB[15:0]. When this pin is logic high and the parallel
interface is selected, byte mode is enabled. In this mode, data is transferred using Data Lines DB[15:8],
and DB 7 functions as HBEN. To obtain the 16-bit conversion result, 2-byte reads are required. When
the serial interface is selected, tie this pin to DGND.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J4Z-MY-F2 | CONVERTER MOD DC/DC 2V 20W |
| VE-J4Y-MY-F1 | CONVERTER MOD DC/DC 3.3V 33W |
| AD7656YSTZ | IC ADC 16BIT 6CH 250KSPS 64LQFP |
| VE-J4Y-MW-F4 | CONVERTER MOD DC/DC 3.3V 66W |
| VI-B53-MW | CONVERTER MOD DC/DC 24V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7656YSTZ-1-RL | 功能描述:IC ADC 16BIT 6CH 250KSPS 64LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7656YSTZ-REEL | 功能描述:IC ADC 16BIT 6CH 250KSPS 64LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7657 | 制造商:AD 制造商全称:Analog Devices 功能描述:250 kSPS, 6-Channel,Simultaneous Sampling, Bipolar 12/14/16-Bit ADC |
| AD7657-1 | 制造商:AD 制造商全称:Analog Devices 功能描述:250 kSPS, 6-Channel, Simultaneous Sampling, Bipolar, 16-/14-/12-Bit ADC |
| AD7657BSTZ | 功能描述:IC ADC 14BIT 6CH 250KSPS 64-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
发布紧急采购，3分钟左右您将得到回复。