- 您现在的位置：买卖IC网 > PDF目录10667 > AD7660ASTZ (Analog Devices Inc)IC ADC 16BIT UNIPOLAR 48-LQFP PDF资料下载
参数资料
| 型号： | AD7660ASTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT UNIPOLAR 48-LQFP |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| 位数： | 16 |
| 采样率（每秒）： | 100k |
| 数据接口： | 串行，并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 25mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 托盘 |
| 输入数目和类型： | 2 个伪差分，单极 |
| 产品目录页面： | 778 (CN2011-ZH PDF) |
| 配用： | EVAL-AD7660CBZ-ND - BOARD EVALUATION FOR AD7660 |
REV. D
AD7660
–16–
Usually, because the AD7660 has a longer acquisition phase
than the conversion phase, the data is read immediately after
conversion. This makes the Master Read after conversion the
most recommended Serial Mode when it can be used. In this
mode, it should be noted that, unlike in other modes, the signal
BUSY returns LOW after the 16 data bits are pulsed out and
not at the end of the conversion phase, which results in a longer
BUSY width.
In Read-during-Conversion Mode, the serial clock and data
toggle at appropriate instants, which minimizes potential
feedthrough between digital activity and the critical conversion
decisions.
SLAVE SERIAL INTERFACE
External Clock
The AD7660 is configured to accept an externally supplied serial
data clock on the SCLK pin when the EXT/
INT pin is held
HIGH. In this mode, several methods can be used to read the
data. When
CS and RD are both LOW, the data can be read
after each conversion or during the following conversion. The
external clock can be either a continuous or discontinuous clock.
A discontinuous clock can be either normally HIGH or normally
LOW when inactive. Figures 18 and 20 show the detailed timing
diagrams of these methods. Usually, because the AD7660 has a
longer acquisition phase than the conversion phase, the data are
read immediately after conversion.
While the AD7660 is performing a bit decision, it is important
that voltage transients not occur on digital input/output pins or
degradation of the conversion result could occur. This is par-
ticularly important during the second half of the conversion
phase because the AD7660 provides error correction circuitry that
can correct for an improper bit decision made during the first half
of the conversion phase. For this reason, it is recommended
that when an external clock is being provided, it is a discon-
tinuous clock that is toggling only when BUSY is LOW or, more
importantly, that it does not transition during the latter half of
BUSY HIGH.
External Discontinuous Clock Data Read after Conversion
This mode is the most recommended of the serial slave modes.
Figure 18 shows the detailed timing diagrams of this method. After
a conversion is complete, indicated by BUSY returning LOW,
the result of this conversion can be read while both
CS and RD are
LOW. The data is shifted out, MSB first, with 16 clock pulses and
is valid on both the rising and falling edge of the clock.
Among the advantages of this method, the conversion performance
is not degraded because there are no voltage transients on the
digital interface during the conversion process.
Another advantage is the ability to read the data at any speed up
to 40 MHz, which accommodates both slow digital host inter-
face and the fastest serial reading.
Finally, in this mode only, the AD7660 provides a “daisy-chain”
feature using the RDC/SDIN input pin for cascading multiple
converters together. This feature is useful for reducing component
count and wiring connections when it is desired as it is, for
instance, in isolated multiconverter applications.
An example of the concatenation of two devices is shown in
Figure 19. Simultaneous sampling is possible by using a common
CNVST signal. It should be noted that the RDC/SDIN input is
latched on the opposite edge of SCLK of the one used to shift out
the data on SDOUT. Therefore, the MSB of the “upstream”
converter just follows the LSB of the “downstream” converter on
the next SCLK cycle. Up to 20 AD7660s running at 100 kSPS
can be daisy-chained using this method.
SCLK
SDOUT
RDC/SDIN
BUSY
DATA OUT
AD7660
#1
(DOWNSTREAM)
BUSY OUT
CNVST
CS
SCLK
AD7660
#2
(UPSTREAM)
RDC/SDIN
SDOUT
SCLK IN
CS IN
CNVST IN
CNVST
CS
Figure 19. Two AD7660s in a Daisy-Chain Configuration
SCLK
SDOUT
D15
D14
D1
D0
D13
X15
X14
X13
X1
X0
Y15
Y14
CS
BUSY
SDIN
EXT/
INT = 1
INVSCLK = 0
t35
t36 t37
t31
t32
t16
t33
X15
X14
X
12
3
14
15
1617
18
RD = 0
t34
Figure 18. Slave Serial Data Timing for Reading (Read after Convert)
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J11-MW-F1 | CONVERTER MOD DC/DC 12V 100W |
| LTC1403AIMSE#PBF | IC ADC 14BIT 2.8MSPS 10-MSOP |
| AD7658BSTZ | IC ADC 12BIT 6CH 250KSPS 64LQFP |
| AD7767BRUZ-1 | ADC 24BIT 64KSPS SAR 16-TSSOP |
| AD7714YRUZ | IC ADC SIGNAL COND 3/5V 24-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7660ASTZ | 制造商:Analog Devices 功能描述:IC 16-BIT ADC |
| AD7660ASTZRL | 功能描述:IC ADC 16BIT UNIPOLAR 48LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7661 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 1 MSPS, Differential, Programmable Input PulSAR ADC |
| AD7661ACP | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 16-bit Parallel/Serial 48-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:100KSPS, 16-BIT ADC INT REF, 2.5LSB - Bulk 制造商:Analog Devices 功能描述:16BIT ADC INT REF 7661 LFSCP-48 |
| AD7661ACPRL | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 16-bit Parallel/Serial 48-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 100KSPS 16BIT PARALLEL/SERL 48LFCSP EP - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:100KSPS, 16-BIT ADC INT REF, 2.5LSB - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。