- 您现在的位置：买卖IC网 > PDF目录10669 > AD7699BCPZ (Analog Devices Inc)IC ADC 8CH 16BIT 500KSPS 20LFCSP PDF资料下载
参数资料
| 型号： | AD7699BCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 8CH 16BIT 500KSPS 20LFCSP |
| 标准包装： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 500k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 32mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 20-LFCSP-VQ |
| 包装： | 托盘 |
| 输入数目和类型： | 8 个单端，单极；4 个差分，单极；4 个差分，双极；4 个伪差分，双极 |
| 产品目录页面： | 778 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7699
Data Sheet
Rev.
| Page 20 of 28
DIGITAL INTERFACE
The AD7699 uses a simple 4-wire interface and is compatible
with SPI, MICROWIRE, QSPI, digital hosts, and DSPs, for
example, Blackfin ADSP-BF53x, SHARC, ADSP-219x, and
ADSP-218x.
The interface uses the CNV, DIN, SCK, and SDO signals and
allows CNV, which initiates the conversion, to be independent
of the readback timing. This is useful in low jitter sampling or
simultaneous sampling applications.
A 14-bit register, CFG[13:0], is used to configure the ADC for
the channel to be converted, the reference selection, and other
components, which are detailed in the Configuration Register,
CFG section.
When CNV is low, reading/writing can occur during conversion,
acquisition, and spanning conversion (acquisition plus conver-
sion), as detailed in the following sections. The CFG word is
updated on the first 14 SCK rising edges, and conversion results
are output on the first 15 (or 16 if busy mode is selected) SCK
falling edges. If the CFG readback is enabled, an additional
14 SCK falling edges are required to output the CFG word
associated with the conversion results, with the CFG MSB
following the LSB of the conversion result.
A discontinuous SCK is recommended because the part is
selected with CNV low, and SCK activity begins to write a new
configuration word and clock out data.
Note that in the following sections, the timing diagrams indicate
digital activity (SCK, CNV, DIN, SDO) during the conversion.
However, due to the possibility of performance degradation,
digital activity should occur only prior to the safe data reading/
circuitry that can correct for an incorrect bit during this time.
From tDATA to tCONV, there is no error correction and conversion
results may be corrupted. The user should configure the AD7699
and initiate the busy indicator (if desired) prior to tDATA. It is also
possible to corrupt the sample by having SCK or DIN transitions
near the sampling instant. Therefore, it is recommended to keep
the digital pins quiet for approximately 30 ns before and 10 ns
after the rising edge of CNV, using a discontinuous SCK whenever
possible to avoid any potential performance degradation.
READING/WRITING DURING CONVERSION, FAST
HOSTS
When reading/writing during conversion (n), conversion
results are for the previous (n 1) conversion, and writing the
CFG is for the next (n + 1) acquisition and conversion.
After the CNV is brought high to initiate conversion, it must be
brought low again to allow reading/writing during conversion.
Reading/writing should only occur up to tDATA and, because this
time is limited, the host must use a fast SCK.
The SCK frequency required is calculated by
DATA
t
Edges
SCK
Number
SCK
f
_
≥
The time between tDATA and tCONV is a safe time when digital
activity should not occur, or sensitive bit decisions may be
corrupt.
READING/WRITING DURING ACQUISITION, ANY
SPEED HOSTS
When reading/writing after conversion, or during acquisition
(n), conversion results are for the previous (n 1) conversion,
and writing is for the (n + 1) acquisition.
For the maximum throughput, the only time restriction is that
the reading/writing take place during the tACQ (min) time. For
slow throughputs, the time restriction is dictated by throughput
required by the user, and the host is free to run at any speed.
Thus for slow hosts, data access must take place during the
acquisition phase.
READING/WRITING SPANNING CONVERSION, ANY
SPEED HOST
When reading/writing spanning conversion, the data access starts
at the current acquisition (n) and spans into the conversion (n).
Conversion results are for the previous (n 1) conversion, and
writing the CFG register is for the next (n + 1) acquisition and
conversion.
Similar to reading/writing during conversion, reading/writing
should only occur up to tDATA. For the maximum throughput,
the only time restriction is that reading/writing take place
during the tACQ (min) + tDATA time.
For slow throughputs, the time restriction is dictated by the
user’s required throughput, and the host is free to run at any
speed. Similar to reading/writing during acquisition, for slow
hosts, the data access must take place during the acquisition
phase with additional time into the conversion.
Note that data access spanning conversion requires the CNV to
be driven high to initiate a new conversion, and data access is
not allowed when CNV is high. Thus, the host must perform
two bursts of data access when using this method.
CONFIGURATION REGISTER, CFG
The AD7699 uses a 14-bit configuration register (CFG[13:0]) as
detailed in Table 8 for configuring the inputs, the channel to be
converted, one-pole filter bandwidth, the reference, and the
channel sequencer. The CFG register is latched (MSB first) on
DIN with 14 SCK rising edges. CFG update is edge dependent,
allowing for asynchronous or synchronous hosts.
B
相关PDF资料 |
PDF描述 |
|---|---|
| ISL55141IRZ-T | IC COMP CMOS HS 18V 16-QFN |
| ISL55141IVZ-T | IC COMP CMOS HS 18V 14-TSSOP |
| LTC2444IUHF#PBF | IC ADC 24BIT HI SPEED 38QFN |
| LTC2445IUHF#PBF | IC ADC 24BIT HI SPEED 38QFN |
| VE-J7R-MY-F3 | CONVERTER MOD DC/DC 7.5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7699BCPZRL7 | 功能描述:IC ADC 8CH 16BIT 500KSPS 20LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7701 | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS 16-Bit A/D Converter |
| AD7701AN | 功能描述:IC ADC 16BIT LC2MOS 20-DIP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7701ANZ | 功能描述:IC ADC 16BIT LC2MOS 20-DIP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7701AQ | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS 16-Bit A/D Converter |
发布紧急采购，3分钟左右您将得到回复。