- 您现在的位置：买卖IC网 > PDF目录10247 > AD7707BR (Analog Devices Inc)IC ADC 16BIT 3CH 20-SOIC PDF资料下载
参数资料
| 型号： | AD7707BR |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/52页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 3CH 20-SOIC |
| 标准包装： | 37 |
| 位数： | 16 |
| 采样率（每秒）： | 500 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 1mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC W |
| 包装： | 管件 |
| 输入数目和类型： | 1 个单端，单极；1 个单端，双极；2 个伪差分，单极；2 个伪差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
AD7707
Rev. B | Page 21 of 52
Clock Register (RS2, RS1, RS0 = 0, 1, 0); Power-On/Reset Status: 0x05
The clock register is an 8-bit register from which data can either be read or to which data can be written. Table 22 outlines the bit
designations for the clock register.
Table 22. Clock Register
Zero (0)
CLKDIS (0)
CLKDIV (0)
CLK (1)
FS2 (0)
FS1 (0)
FS0 (1)
Table 23. Clock Register Bit Descriptions
Bit
Description
Zero
Zero. A zero must be written to these bits to ensure correct operation of the AD7707. Failure to do so may result in unspecified
operation of the device.
CLKDIS
Master clock disable bit. A Logic 1 in this bit disables the master clock from appearing at the MCLK OUT pin. When disabled, the
MCLK OUT pin is forced low. This feature allows the user the flexibility of using the MCLK OUT as a clock source for other devices
in the system or of turning off the MCLK OUT as a power saving feature. When using an external master clock on the MCLK IN
pin, the AD7707 continues to have internal clocks and converts normally with the CLKDIS bit active. When using a crystal
oscillator or ceramic resonator across the MCLK IN and MCLK OUT pins, the AD7707 clock is stopped and no conversions take
place when the CLKDIS bit is active.
CLKDIV
Clock divider bit. With this bit at a Logic 1, the clock frequency appearing at the MCLK IN pin is divided by two before being used
internally by the AD7707. For example, when this bit is set to 1, the user can operate with a 4.9152 MHz crystal between MCLK
IN and MCLK OUT, and internally the part operates with the specified 2.4576 MHz. With this bit at a Logic 0, the clock frequency
appearing at the MCLK IN pin is the frequency used internally by the part.
CLK
Clock bit. This bit should be set in accordance with the operating frequency of the AD7707. If the device has a master clock
frequency of 2.4576 MHz (CLKDIV = 0) or 4.9152 MHz (CLKDIV = 1), then this bit should be set to a 1. If the device has a master
clock frequency of 1 MHz (CLKDIV = 0) or 2 MHz (CLKDIV = 1), this bit should be set to a 0. This bit sets up the appropriate scaling
currents for a given operating frequency and also chooses (along with FS2, FS1 and FS0) the output update rate for the device. If
this bit is not set correctly for the master clock frequency of the device, then the AD7707 may not operate to specification.
FS2, FS1,
FS0
Filter selection bits. Along with the CLK bit, FS2, FS1, and FS0 determine the output update rate, filter first notch, and 3 dB
frequency as outlined in Table 24. The on-chip digital filter provides a sinc3 (or Sinx/x3) filter response. Placing the first notch at
10 Hz places notches at both 50 Hz and 60 Hz, giving better than 150 dB rejection at these frequencies. In association with the
gain selection, the filter cutoff also determines the output noise of the device. Changing the filter notch frequency, as well as the
selected gain, impacts resolution. Table 7 to Table 13 show the effect of filter notch frequency and gain on the output noise and
effective resolution of the part. The output data rate (or effective conversion time) for the device is equal to the frequency
selected for the first notch of the filter. For example, if the first notch of the filter is selected at 50 Hz, a new word is available at a
50 Hz output rate, or every 20 ms. If the first notch is at 500 Hz, a new word is available every 2 ms. A calibration should be
initiated when any of these bits are changed.
The settling time of the filter to a full-scale step input is worst-case 4 × 1/(output data rate). For example, with the filter first
notch at 50 Hz, the settling time of the filter to a full-scale step input is 80 ms maximum. If the first notch is at 500 Hz, the
settling time is 8 ms maximum. This settling time can be reduced to 3 × 1/(output data rate) by synchronizing the step input
change to a reset of the digital filter. In other words, if the step input takes place with the FSYNC bit high, the settling time is 3 ×
1/(output data rate) from when the FSYNC bit returns low.
The 3 dB frequency is determined by the programmed first notch frequency according to the following relationship:
filter 3 dB frequency = 0.262 × filter first notch frequency
相关PDF资料 |
PDF描述 |
|---|---|
| VE-23Y-MV-F4 | CONVERTER MOD DC/DC 3.3V 99W |
| VE-23J-CU-F1 | CONVERTER MOD DC/DC 36V 200W |
| AD7575JRZ | IC ADC 8BIT LC2MOS W/HOLD 18SOIC |
| VE-23Y-MV-F3 | CONVERTER MOD DC/DC 3.3V 99W |
| VE-23H-CU-F4 | CONVERTER MOD DC/DC 52V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7707BR-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 500sps 16-bit Serial 20-Pin SOIC W T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.5KSPS 16BIT SERL 20SOIC W - Tape and Reel |
| AD7707BR-REEL7 | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 500sps 16-bit Serial 20-Pin SOIC W T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.5KSPS 16BIT SERL 20SOIC W - Tape and Reel |
| AD7707BRU | 功能描述:IC ADC 16BIT 3CH 20-TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7707BRU-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 500sps 16-bit Serial 20-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.5KSPS 16BIT SERL 20TSSOP - Tape and Reel |
| AD7707BRU-REEL7 | 功能描述:IC ADC 16BIT 3CH 20-TSSOP T/R RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。