- 您现在的位置：买卖IC网 > PDF目录10092 > AD7710AN (Analog Devices Inc)IC ADC SIGNAL CONDITIONING 24DIP PDF资料下载
参数资料
| 型号： | AD7710AN |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC SIGNAL CONDITIONING 24DIP |
| 标准包装： | 15 |
| 位数： | 24 |
| 采样率（每秒）： | 1.03k |
| 数据接口： | 串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 45mW |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 24-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 24-PDIP |
| 包装： | 管件 |
| 输入数目和类型： | 2 个差分，单极；2 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
REV. G
–24–
AD7710
SIMPLIFYING THE EXTERNAL CLOCKING MODE
INTERFACE
In many applications, the user may not need to write to the on-chip
calibration registers. In this case, the serial interface to the AD7710
in external clocking mode can be simplified by connecting the
TFS
line to the A0 input of the AD7710 (see Figure 14). This means
that any write to the device will load data to the control register
(because A0 is low while
TFS is low), and any read to the de-
vice will access data from the output data register or from the
calibration registers (because A0 is high while
RFS is low). Note
that in this arrangement the user does not have the capability of
reading from the control register.
AD7710
SDATA
SCLK
TFS
A0
FOUR
INTERFACE
LINES
RFS
Figure 14. Simplified Interface with
TFS Connected to A0
Another method of simplifying the interface is to generate the
TFS signal from an inverted RFS signal. However, generating
the signals the opposite way around (
RFS from an inverted
TFS) will cause writing errors.
MICROCOMPUTER/MICROPROCESSOR INTERFACING
The AD7710’s flexible serial interface allows for easy interface
to most microcomputers and microprocessors. Figure 15 shows
a flowchart for a typical programming sequence for reading data
from the AD7710 to a microcomputer, while Figure 16 shows a
flowchart for writing data to the AD7710. Figures 17, 18, and
19 show some typical interface circuits.
Figure 15 shows continuous read operations from the AD7710
output register, where the
DRDY line is continuously polled.
Depending on the microprocessor configuration, the
DRDY line
may come to an interrupt input, in which case the
DRDY will
automatically generate an interrupt without being polled. Read-
ing the serial buffer could be anything from one read operation
up to three read operations (where 24 bits of data are read into
an 8-bit serial register). A read operation to the control/calibra-
tion registers is similar, but, in this case, the status of
DRDY
can be ignored. The A0 line is brought low when the
RFS line
is brought low during a read register.
The flowchart also shows the bits being reversed after they have
been read in from the serial port. This depends on whether the
microprocessor expects the MSB of the word first or the LSB of
the word first. The AD7710 outputs the MSB first.
Figure 16 shows a single 24-bit write operation to the AD7710
control or calibration registers. This shows data being trans-
ferred from data memory to the accumulator before being writ-
ten to the serial buffer. Some microprocessor systems allow data
to be written directly to the serial buffer from data memory.
Writing data to the serial buffer from the accumulator generally
consists of either two or three write operations, depending on
the size of the serial buffer.
NO
YES
BRING
RFS LOW
3
REVERSE
ORDER OF BITS
BRING
RFS HIGH
POLL DRDY
CONFIGURE AND
INITIALIZE
C/ P
SERIAL PORT
DRDY
LOW?
BRING
RFS, TFS HIGH
START
READ
SERIAL BUFFER
Figure 15. Flowchart for Continuous Read Operations
to the AD7710
Figure 16 also shows the option of the bits being reversed before
being written to the serial buffer. This depends on whether the
first bit transmitted by the microprocessor is the MSB or the
LSB. The AD7710 expects the MSB as the first bit in the data
stream. In cases where the data is being read or being written in
bytes and the data has to be reversed, the bits have to be reversed
for every byte.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-24Z-MV-F3 | CONVERTER MOD DC/DC 2V 60W |
| IDT72V221L15JI8 | IC FIFO SYNC 1KX9 15NS 32PLCC |
| LT1785AHN8#PBF | IC TXRX RS485/RS422 60V 8-DIP |
| LTC2380IDE-16#TRPBF | IC ADC 16BIT 2MSPS 16-DFN |
| IDT72V221L10J8 | IC FIFO SYNC 1KX9 10NS 32PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7710ANZ | 功能描述:IC ADC SIGNAL CONDITIONING 24DIP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7710AQ | 功能描述:IC ADC 24BIT DIFF INP 24-CDIP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7710AR | 功能描述:IC ADC 24BIT DIFF INP 24-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7710AR-REEL | 功能描述:IC ADC 24BIT DIFF INP 24-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7710AR-REEL7 | 功能描述:IC ADC 24BIT DIFF INP 24-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。