- 您现在的位置：买卖IC网 > PDF目录10231 > AD7715AR-5 (Analog Devices Inc)IC ADC 16BIT 5V 16-SOIC PDF资料下载
参数资料
| 型号： | AD7715AR-5 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 15/40页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 5V 16-SOIC |
| 标准包装： | 47 |
| 位数： | 16 |
| 采样率（每秒）： | 500 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 9.5mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，单极；1 个差分，双极 |
| 配用： | EVAL-AD7715-3EBZ-ND - BOARD EVALUATION FOR AD7715 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
AD7715
Rev. D | Page 22 of 40
Filter Characteristics
The AD7715’s digital filter is a low-pass filter with a (sinx/x)3
response (also called sinc3). The transfer function for this filter
is described in the z-domain by
3
1
)
(
×
=
z
N
z
H
N
and in the frequency domain by
3
1
)
(
×
π
×
π
×
=
S
f
Sin
f
N
Sin
N
f
H
where N is the ratio of the modulator rate to the output rate and
fMOD is the modulator rate.
Figure 6 shows the filter frequency response for a cutoff frequency
of 15.72 Hz which corresponds to a first filter notch frequency
of 60 Hz. The plot is shown from dc to 390 Hz. This response is
repeated at either side of the digital filter’s sample frequency
and at either side of multiples of the filter’s sample frequency.
FREQUENCY (Hz)
0
–40
–60
–80
–100
–120
–140
–160
–180
–200
–220
–20
–240
360
0
300
180
120
60
240
GA
IN
(
d
B
)
08
51
9-
0
06
Figure 6. Frequency Response of AD7715 Filter
The response of the filter is similar to that of an averaging filter
but with a sharper roll-off. The output rate for the digital filter
corresponds with the positioning of the first notch of the filter’s
frequency response. Thus, for the plot of Figure 6 where the
output rate is 60 Hz, the first notch of the filter is at 60 Hz. The
notches of this (sinx/x)3 filter are repeated at multiples of the
first notch. The filter provides attenuation of better than 100 dB
at these notches.
The cutoff frequency of the digital filter is determined by the
value loaded to the FS0 to FS1 bits in the setup register. program-
ming a different cutoff frequency via FS0 and FS1 does not alter
the profile of the filter response; it changes the frequency of the
notches. The output update of the part and the frequency of the
first notch correspond.
Because the AD7715 contains this on-chip, low-pass filtering,
there is a settling time associated with step function inputs and
data on the output is invalid after a step change until the settling
time has elapsed. The settling time depends upon the output
rate chosen for the filter. The settling time of the filter to a full-
scale step input can be up 4 times the output data period. For a
synchronized step input (using the FSYNC function), the
settling time is 3 times the output data period.
Post-Filtering
The on-chip modulator provides samples at a 19.2 kHz output
rate with fCLKIN at 2.4576 MHz. The on-chip digital filter decimates
these samples to provide data at an output rate that corresponds
to the programmed output rate of the filter. Because the output
data rate is higher than the Nyquist criterion, the output rate
for a given bandwidth satisfys most application requirements.
However, there may be some applications that require a higher
data rate for a given bandwidth and noise performance.
Applications that need this higher data rate do require some
post-filtering following the digital filter of the AD7715.
For example, if the required bandwidth is 7.86 Hz but the
required update rate is 100 Hz, the data can be taken from the
AD7715 at the 100 Hz rate giving a 3 dB bandwidth of 26.2 Hz.
Post-filtering can be applied to this to reduce the bandwidth
and output noise, to the 7.86 Hz bandwidth level, while
maintaining an output rate of 100 Hz.
Post-filtering can also be used to reduce the output noise from
the device for bandwidths below 13.1 Hz. At a gain of 128 and
a bandwidth of 13.1 Hz, the output rms noise is 520 nV. This is
essentially device noise or white noise and because the input is
chopped, the noise has a primarily flat frequency response. By
reducing the bandwidth below 13.1 Hz, the noise in the resultant
pass-band can be reduced. A reduction in bandwidth by a factor
of 2 results in a reduction of approximately 1.25 in the output
rms noise. This additional filtering results in a longer settling time.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27467E13A8S | CONN PLUG 8POS STRAIGHT W/SCKT |
| SP202ECT-L/TR | IC DVR/RCVR RS232 QUAD 16WSOIC |
| MS27484T10A98P | CONN PLUG 6POS STRAIGHT W/PINS |
| LTC1418ACG#TR | IC A/D CONV 14BIT SRL&PAR 28SSOP |
| SP232EET-L/TR | IC DVR/RCVR RS232 5V SGL 16WSOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7715AR-5REEL | 功能描述:IC ADC 16BIT SIGMA-DELTA 16-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7715ARU-3 | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 19.2ksps 16-bit Serial 16-Pin TSSOP |
| AD7715ARU-3REEL | 功能描述:IC ADC 16BIT SIGMA-DELTA 16TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7715ARU-3REEL7 | 功能描述:IC ADC 16BIT SIGMA-DELTA 16TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7715ARU-5 | 功能描述:IC ADC 16BIT SIGMA-DELTA 16TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。