- 您现在的位置：买卖IC网 > PDF目录1983 > AD7764BRUZ-REEL7 (Analog Devices Inc)IC ADC 24BIT S/D 312KSPS 28TSSOP PDF资料下载
参数资料
| 型号： | AD7764BRUZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 21/33页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT S/D 312KSPS 28TSSOP |
| 标准包装： | 1,000 |
| 位数： | 24 |
| 采样率（每秒）： | 312k |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 371mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个差分，单极；1 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
AD7764
Rev. A | Page 27 of 32
DECOUPLING AND LAYOUT INFORMATION
SUPPLY DECOUPLING
The decoupling of the supplies applied to the AD7764 is
important in achieving maximum performance. Each supply
pin must be decoupled to the correct ground pin with a 100 nF,
0603 case size capacitor.
Pay particular attention to decoupling Pin 7 (AVDD2) directly to
the nearest ground pin (Pin 8). The digital ground pin AGND2
(Pin 20) is routed directly to ground. Also, connect REFGND
(Pin 26) directly to ground.
The DVDD (Pin 17) and AVDD3 (Pin 28) supplies should be
decoupled to the ground plane at a point away from the device.
It is advised to decouple the supplies that are connected to the
following supply pins through 0603 size, 100 nF capacitors to a
star ground point linked to Pin 23 (AGND1):
VREF+ (Pin 27)
AVDD4 (Pin 25)
AVDD1 (Pin 24)
AVDD2 (Pin 21)
A layout decoupling scheme for these supplies, which connect
to the right side of the AD7764, is shown in Figure 51. Note the
star-point ground created at Pin 23.
06518-
133
AVDD2 (PIN 21)
VREF+ (PIN 27)
GND
PIN 23
STAR-POINT
GND
AVDD4
(PIN 25)
AVDD3 (PIN 28)
VIA TO GND
FROM PIN 20
AVDD1 (PIN 24)
GND
PIN 15
Figure 51. Supply Decoupling
REFERENCE VOLTAGE FILTERING
A low noise reference source, such as the ADR444 or ADR434
(4.096 V), is suitable for use with the AD7764. The reference
voltage supplied to the AD7764 should be decoupled and
filtered as shown in Figure 52.
The recommended scheme for the reference voltage supply is a
200 Ω series resistor connected to a 100 μF tantalum capacitor,
followed by a 10 nF decoupling capacitor very close to the
VREF+ pin.
06518-
134
7.5V
VOUT
2
VIN
6
4
10F
100nF
+
100nF
+
ADR444
GND
VREF+
PIN 27
100F
200
Figure 52. Reference Connection
DIFFERENTIAL AMPLIFIER COMPONENTS
The components recommended for use around the on-chip
differential amplifier are detailed in Table 7. Matching the
components on both sides of the differential amplifier is
important to minimize distortion of the signal applied to the
amplifier. A tolerance of 0.1% or better is required for these
components. Symmetrical routing of the tracks on both sides
of the differential amplifier also assists in achieving stated
performance. Figure 53 shows a typical layout for the com-
ponents around the differential amplifier. Note that the traces
for both differential paths are made as symmetrical as possible
and that the feedback resistors and capacitors are placed on the
underside of the PCB to enable the simplest routing.
06518-
135
RFB
CFB
RIN
VINA–
VINA+
Figure 53. Typical Layout Structure for Surrounding Components
LAYOUT CONSIDERATIONS
Whereas using the correct components is essential to achieve
optimum performance, the correct layout is equally as
important. The AD7764 product page on www.analog.com
contains the Gerber files for the AD7764 evaluation board. The
Gerber files should be used as a reference when designing any
system using the AD7764.
The use of ground planes should be carefully considered. To
ensure that the return currents through the decoupling
capacitors are flowing to the correct ground pin, the ground
side of the capacitors should be as close to the ground pin
associated with that supply, as recommended in the Supply
Decoupling section.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7765BRUZ-REEL7 | IC ADC 24BIT S/D 156KSPS 28TSSOP |
| AD7766BRUZ-RL7 | IC ADC 24BIT 128KSPS SAR 16TSSOP |
| AD7767BRUZ-RL7 | ADC 24BIT 15MW 128KSPS 16TSSOP |
| AD7776ARZ | IC ADC 10BIT 1CHAN HS 24SOIC |
| AD7780BRZ-REEL | IC ADC 24BIT 1CH LP SD 14SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7765 | 制造商:AD 制造商全称:Analog Devices 功能描述:24-Bit, 8.5 mW, 109 dB, 128/64/32 kSPS ADCs |
| AD7765_07 | 制造商:AD 制造商全称:Analog Devices 功能描述:24-Bit, 156 kSPS, 112 dB ヒ-ツ ADC with On-Chip Buffers and Serial Interface |
| AD7765BRUZ | 功能描述:IC ADC 24BIT S/D 156KSPS 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7765BRUZ-REEL7 | 功能描述:IC ADC 24BIT S/D 156KSPS 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7766 | 制造商:AD 制造商全称:Analog Devices 功能描述:24-Bit, 8.5 mW, 109 dB, 128/64/32 kSPS ADCs |
发布紧急采购，3分钟左右您将得到回复。