- 您现在的位置：买卖IC网 > PDF目录9712 > AD7877ACPZ-REEL (Analog Devices Inc)IC ADC 12BIT TOUCHSCREEN 32LFCSP PDF资料下载
参数资料
| 型号： | AD7877ACPZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/45页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT TOUCHSCREEN 32LFCSP |
| 标准包装： | 5,000 |
| 类型： | 电阻 |
| 触摸面板接口： | 4 线 |
| 输入数/键： | 1 TSC |
| 分辨率（位）： | 12 b |
| 评估套件： | 可供 |
| 数据接口： | 串行，SPI? |
| 数据速率/采样率 (SPS，BPS)： | 125k |
| 电压基准： | 外部，内部 |
| 电源电压： | 2.7 V ~ 5.25 V |
| 电流 - 电源： | 1µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-VQ |
| 包装： | 带卷 (TR) |
| 配用： | EVAL-AD7877EBZ-ND - BOARD EVALUATION FOR AD7877 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
Data Sheet
AD7877
Rev. D | Page 17 of 44
It is only during the sample or acquisition phase of the ADC
operation of the AD7877 that noise from the LCD screen has an
effect on the ADC measurements. During the hold or
conversion phase, the noise has no effect, because the voltage at
the input of the ADC has already been acquired. Therefore, to
minimize the effect of noise on the touch screen measurements,
the ADC acquisition phase should be halted.
The LCD control signal should be applied to the STOPACQ pin.
To ensure that acquisition never occurs during the noisy period
when the LCD signal is active, the AD7877 monitors this signal.
No acquisitions take place when the control signal is active. Any
acquisition that is in progress when the signal becomes active is
aborted and restarts when the signal becomes inactive again.
To accommodate signals of different polarities on the
STOPACQ pin, a user-programmable register bit is used to
indicate whether the signal is active high or low. The POL bit
is Bit 3 in Control Register 2, Address 0x02. Setting POL to 1
indicates that the signal on STOPACQ is active high; setting
POL to 0 indicates that it is active low. POL defaults to 0 on
power-up. To disable monitoring of STOPACQ, the pin should
be tied low if POL = 1, or tied high if POL = 0. Under no
circumstances should the pin be left floating.
The signal on STOPACQ has no effect while the ADC is in
conversion mode, or during the first conversion delay time.
(See the Control Registers section for details on the first
conversion delay.)
When enabled, the STOPACQ monitoring function is imple-
mented on all input channels to the ADC: AUX1, AUX2, BAT1,
BAT2, TEMP1, and TEMP2, as well as on the touch screen
input channels.
TEMPERATURE MEASUREMENT
Two temperature measurement options are available on the
AD7877: the single conversion method and the differential
conversion method. The single conversion method requires
only a single measurement on ADC Channel 1000b. Whereas
differential conversion requires two measurements, one on
ADC Channel 1000b and a second on ADC Channel 1001b.
The results are stored in the results registers with Address 11000b
(TEMP1) and Address 11001b (TEMP2). The AD7877 does not
provide an explicit output of the temperature reading; the
system must perform some external calculations. Both methods
are based on an on-chip diode measurement.
Single Conversion Method
The single conversion method makes use of the fact that the
temperature coefficient of a silicon diode is approximately
2.1 mV/°C. However, this small change is superimposed on
the diode forward voltage, which can have a wide tolerance. It
is, therefore, necessary to calibrate by measuring the diode
voltage at a known temperature to provide a baseline from
which the change in forward voltage with temperature can be
measured. This method provides a resolution of approximately
0.3°C and a predicted accuracy of ±2.5°C.
The temperature limit comparison is performed on the result in
the TEMP1 results register, which is simply the measurement of
the diode forward voltage. The values programmed into the high
and low limits should be referenced to the calibrated diode for-
ward voltage to make accurate limit comparisons. An example
is shown in the Limit Comparison section.
Differential Conversion Method
The differential conversion method is a 2-point measurement.
The first measurement is performed with a fixed bias current
into a diode (when the TEMP1 channel is selected), and the
second measurement is performed with a fixed multiple of the
bias current into the same diode (when the TEMP2 channel is
selected). The voltage difference in the diode readings is pro-
portional to absolute temperature and is given by the following
formula:
VBE = (kT/q) × (ln N)
(4)
where:
VBE represents the diode voltage.
N is the bias current multiple (typical value for AD7877 = 120).
k is Boltzmann’s constant.
q is the electron charge.
This method provides a resolution of approximately 1.6°C, and
a guaranteed accuracy of ±4°C without calibration. Determina-
tion of the N value on a part-by-part basis improves accuracy.
Assuming a current multiple of 120, which is a typical value
for the AD7877, taking Boltzmann’s constant, k = 1.38054 ×
1023 electrons V/°K, the electron charge q = 1.602189 × 1019,
then T, the ambient temperature in Kelvin, would be calculated
as follows:
VBE = (kT/q) × (ln N)
T°k = (VBE × q)/(k × ln N)
= (VBE × 1.602189 × 1019)/(1.38054 × 1023 × 4.65)
T°C = 2.49 × 120 × VBE 273
VBE is calculated from the difference in readings from the first
conversion to the second conversion. The user must perform
the calculations to get VBE, and then calculate the temperature
value in degrees. Figure 33 shows a block diagram of the
temperature measurement circuit.
03796-
0
1
TEMP1
TEMP2
MUX
ADC
I
VBE
I20 × I
Figure 33. Block Diagram of Temperature Measurement Circuit
相关PDF资料 |
PDF描述 |
|---|---|
| MS3106R32-17PX | CONN PLUG 4POS STRAIGHT W/PINS |
| MS3122E14-5SW | CONN RCPT 5POS BOX MNT W/SCKT |
| MS3126F20-41PY | CONN PLUG 41POS STRAIGHT W/PINS |
| M83723/82W803N | CONN RCPT 3POS WALL MT W/SCKT |
| MS3126F20-41PX | CONN PLUG 41POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7877ACPZ-REEL7 | 功能描述:IC ADC 12BIT TOUCHSCREEN 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:- 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD7877WACPZ-REEL7 | 功能描述:IC CTRLR TOUCH SCREEN 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:- 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD7878 | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878AQ | 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12 BIT ADC IC - Bulk |
| AD7878BQ | 功能描述:IC ADC 12BIT W/DSP INT 28-CDIP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:250 系列:- 位数:12 采样率（每秒）:1.8M 数据接口:并联 转换器数目:1 功率耗散（最大）:1.82W 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-LQFP 供应商设备封装:48-LQFP（7x7） 包装:管件 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。