- 您现在的位置：买卖IC网 > PDF目录9712 > AD7877ACPZ-REEL (Analog Devices Inc)IC ADC 12BIT TOUCHSCREEN 32LFCSP PDF资料下载
参数资料
| 型号： | AD7877ACPZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/45页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT TOUCHSCREEN 32LFCSP |
| 标准包装： | 5,000 |
| 类型： | 电阻 |
| 触摸面板接口： | 4 线 |
| 输入数/键： | 1 TSC |
| 分辨率（位）： | 12 b |
| 评估套件： | 可供 |
| 数据接口： | 串行，SPI? |
| 数据速率/采样率 (SPS，BPS)： | 125k |
| 电压基准： | 外部，内部 |
| 电源电压： | 2.7 V ~ 5.25 V |
| 电流 - 电源： | 1µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-VQ |
| 包装： | 带卷 (TR) |
| 配用： | EVAL-AD7877EBZ-ND - BOARD EVALUATION FOR AD7877 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
AD7877
Data Sheet
Rev. D | Page 16 of 44
For greater accuracy, the ratiometric method has two significant
advantages:
The reference to the ADC is provided from the actual
voltage across the screen; therefore, when the voltage drops
across the switches, it has no effect.
Because the measurement is ratiometric, it does not matter
if the voltage across the screen varies in the long term.
However, it must not change after the signal has been
acquired.
The disadvantage of the ratiometric method is that the screen
must be powered up at all times because it provides the
reference voltage for the ADC.
TOUCH-PRESSURE MEASUREMENT
The pressure applied to the touch screen via a pen or finger can
also be measured with the AD7877 using some simple calcula-
tions. The contact resistance between the X and Y plates is
measured providing a good indication of the size of the
depressed area and, therefore, the applied pressure. The area of
the spot that is touched is proportional to the size of the object
touching it. The size of this resistance (RTOUCH) can be calculated
using two different methods.
First Method
The first method requires the user to know the total resistance
of the X-plate tablet (RX). Three touch screen conversions are
required:
Measurement of the X position, XPOSITION (Y+ input).
Measurement of the Y input with the excitation voltage
applied to Y+ and X (Z1 measurement).
Measurement of the X+ input with the excitation voltage
applied to Y+ and X (Z2 measurement).
These three measurements are illustrated in Figure 31.
The AD7877 has two special ADC channel settings that
configure the X and Y switches for Z1 and Z2 measurement and
store the results in the Z1 and Z2 results registers. The Z1
measurement is ADC Channel 1010b, and the result is stored in
the register with Read Address 11010b. The Z2 measurement is
ADC Channel 0010b, and the result is stored in the register with
Read Address 10010b.
The touch resistance can then be calculated using the following
equation:
RTOUCH = (RXPlate) × (XPOSITION /4096 × [Z2/Z1) 1]
(2)
03796-009
Y–
Y+
X–
X+
TOUCH
RESISTANCE
MEASURE
Z1 POSITION
X–
X+
Y–
Y+
TOUCH
RESISTANCE
MEASURE
X POSITION
Y–
Y+
X–
X+
TOUCH
RESISTANCE
MEASURE
Z2 POSITION
Figure 31. Three Measurements Required for Touch Pressure
Second Method
The second method requires the user to know the resistance of
the X-plate and Y-plate tablets. Three touch screen conversions
are required, a measurement of the X position (XPOSITION),
Y position (YPOSITION), and Z1 position.
The following equation also calculates the touch resistance:
RTOUCH = RXPlate × (XPOSITION /4096) × [(4096/Z1) 1]
RYPlate × [1 (YPOSITION/4096)]
(3)
STOPACQ PIN
As previously explained in the Touch Screen Principles section,
touch screens are composed of two resistive layers, normally
placed over an LCD screen. Because these layers are in close
proximity to the LCD screen, noise can be coupled from the
screen onto these resistive layers, causing errors in the touch
screen positional measurements.
For example, a jitter might be noticeable in the cursor on-screen.
In most LCD touch screen systems, a signal, such as an LCD
invert signal or other control signal, is present, and noise is
usually coupled onto the touch screen during the active period
of this signal (see Figure 32).
03796-010
LCD SIGNAL
TOUCH SCREEN
SIGNAL
NOISY
PERIOD
NOISY
PERIOD
Figure 32. Effect of LCD Noise on Touch Screen Measurements
相关PDF资料 |
PDF描述 |
|---|---|
| MS3106R32-17PX | CONN PLUG 4POS STRAIGHT W/PINS |
| MS3122E14-5SW | CONN RCPT 5POS BOX MNT W/SCKT |
| MS3126F20-41PY | CONN PLUG 41POS STRAIGHT W/PINS |
| M83723/82W803N | CONN RCPT 3POS WALL MT W/SCKT |
| MS3126F20-41PX | CONN PLUG 41POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7877ACPZ-REEL7 | 功能描述:IC ADC 12BIT TOUCHSCREEN 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:- 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD7877WACPZ-REEL7 | 功能描述:IC CTRLR TOUCH SCREEN 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:- 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD7878 | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface |
| AD7878AQ | 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12 BIT ADC IC - Bulk |
| AD7878BQ | 功能描述:IC ADC 12BIT W/DSP INT 28-CDIP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:250 系列:- 位数:12 采样率（每秒）:1.8M 数据接口:并联 转换器数目:1 功率耗散（最大）:1.82W 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-LQFP 供应商设备封装:48-LQFP（7x7） 包装:管件 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。