- 您现在的位置：买卖IC网 > PDF目录10679 > AD7888ARUZ-REEL7 (Analog Devices Inc)IC ADC 12BIT SRL 125KSPS 16TSSOP PDF资料下载
参数资料
| 型号： | AD7888ARUZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/17页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT SRL 125KSPS 16TSSOP |
| 标准包装： | 1 |
| 位数： | 12 |
| 采样率（每秒）： | 125k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 3.5mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 标准包装 |
| 输入数目和类型： | 8 个单端，单极 |
| 其它名称： | AD7888ARUZ-REEL7DKR |
AD7888
–11–
MODES OF OPERATION
The AD7888 has a number of different modes of operation.
These are designed to provide flexible power management
options. These options can be chosen to optimize the power
dissipation/throughput rate ratio for differing application require-
ments. The modes of operation are controlled by the PM1 and
PM0 bits of the Control Register as outlined previously.
Normal Mode (PM1 = 0, PM0 = 0)
This mode is intended for fastest throughput rate performance
as the user does not have to worry about any power-up times
with the AD7888 remaining fully powered all the time. Figure
13 shows the general diagram of the operation of the AD7888 in
this mode.
The data presented to the AD7888 on the DIN line during the
first eight clock cycles of the data transfer are loaded to the
Control Register. The part will remain powered up at the end of
the conversion as long as PM1 and PM0 were set to zero in the
write during that conversion. To continue to operate in this
mode, the user must ensure that PM1 and PM0 are both loaded
with 0 on every data transfer.
The falling edge of
CS initiates the sequence and the input
signal is sampled on the second rising edge of the SCLK input.
Sixteen serial clock cycles are required to complete the conver-
sion and access the conversion result. Once a data transfer is
complete (
CS has returned high), another conversion can be
initiated immediately by bringing
CS low again.
Full Shutdown (PM1 = 0, PM0 = 1)
In this mode, all internal circuitry on the AD7888, including the
on-chip reference, is powered-down. The part retains the infor-
mation in the Control Register during full shutdown. The part
remains in full shutdown until the power management bits are
changed. If the power management bits are changed to PM1 = 1
and PM0 = 0, i.e., the autoshutdown mode, the part will remain
in shutdown (now in autoshutdown) but will power up once a
conversion is initiated after that (see Power-Up Times section).
The part changes mode as soon as the control register has been
updated, so if the part is in full shutdown mode and the power
management bits are changed to PM1 = PM0 = 0, i.e., normal
mode, then the part will power up on the 16th SCLK rising edge.
Autoshutdown (PM1 = 1, PM0 = 0)
In this mode, the AD7888 automatically enters its power-down
mode at the end of every conversion. Figure 14a shows the
general diagram of the operation of the AD7888 in this mode.
When
CS goes from high to low, all on-chip circuitry will start
to power up on the next falling edge of SCLK. On the sixteenth
SCLK rising edge the part will power down again. It takes
approximately 5
s for the AD7888 internal circuitry to be fully
powered up. As a result, a conversion (or sample-and-hold
acquisition) should not be initiated during this 5
s. The input
signal is sampled on the second rising edge of SCLK following
the
CS falling edge. The user should ensure that 5
s elapse
between the first falling edge of SCLK after the falling edge of
SCLK
4 LEADING ZEROES + CONVERSION RESULT
CS
DOUT
DATA IN
DIN
THE PART REMAINS POWERED UP
AT ALL TIMES AS PM1 AND PM0 = 0
1
16
CONTROL REGISTER DATA IS LOADED ON THE
FIRST 8 CLOCKS. PM1 AND PM0 = 0 TO KEEP
THE PART IN THIS MODE
Figure 13. Normal-Mode Operation
SCLK
4 LEADING ZEROES + CONVERSION RESULT
CS
DOUT
DATA IN
DIN
THE PART POWERS UP FROM
SHUTDOWN ON SCLK FALLING EDGE AS
PM1 = 1 AND PM0 = 0
1
16
4 LEADING ZEROES + CONVERSION RESULT
DATA IN
1
16
2
t10 = 5 s
THE PART ENTERS
SHUTDOWN AT THE END OF
CONVERSION AS PM1 = 1 AND PM0 = 0
CONTROL REGISTER DATA IS LOADED ON THE
FIRST 8 CLOCKS. PM1 = 1 AND PM0 = 0
PM1 = 1 AND PM0 = 0 TO KEEP THE
PART IN THIS MODE
Figure 14a. Autoshutdown Operation
REV. C
相关PDF资料 |
PDF描述 |
|---|---|
| MC10H115PG | IC RECEIVER QUAD LINE ECL 16DIP |
| ADCMP562BRQ | IC COMPARATOR PECL DUAL 20QSOP |
| ADCMP551BRQ | IC COMPARATOR PECL/LVPECL 16QSOP |
| AD790JR-REEL | IC COMPARATOR PREC W/LATCH 8SOIC |
| LT1016IS8 | IC COMPARATOR 10NS HI-SPD 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7888ARZ | 功能描述:IC ADC 12BIT 8CH SRL 16-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7888ARZ-REEL | 功能描述:IC ADC 12BIT 8CH SRL 16-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| AD7888ARZ-REEL7 | 功能描述:IC ADC 12BIT 8CH SRL 16-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7888BR | 制造商:Analog Devices 功能描述:ADC Single SAR 125ksps 12-bit Serial 16-Pin SOIC N |
| AD7888BR-REEL | 功能描述:IC ADC 12BIT 8CHAN SRL 16SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。