- 您现在的位置：买卖IC网 > PDF目录1984 > AD7938BCPZ-6 (Analog Devices Inc)IC ADC 12BIT 8CH 625KSPS 32LFCSP PDF资料下载
参数资料
| 型号： | AD7938BCPZ-6 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 8CH 625KSPS 32LFCSP |
| 标准包装： | 1 |
| 位数： | 12 |
| 采样率（每秒）： | 625k |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 7.5mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-VQ |
| 包装： | 托盘 |
| 输入数目和类型： | 8 个单端，单极；4 个差分，单极；4 个伪差分，单极；7 伪差分，单极 |
| 配用： | EVAL-AD7938CBZ-ND - EVAL BOARD FOR AD7938 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Data Sheet
AD7938-6
Rev. C | Page 19 of 32
047
51
-03
2
*ADDITIONAL PINS OMITTED FOR CLARITY.
VREF
p-p
VIN+
VIN–
VREF
p-p
AD7938-6*
VREF (V)
CO
M
O
N-
M
O
DE
RAN
G
E
(
V
)
4.5
4.0
3.0
1.5
2.0
2.5
3.5
1.0
0.5
0
0.1
0.6
1.6
1.1
2.1
2.6
04
75
1-
0
34
TA = 25°C
COMMON-MODE
VOLTAGE
Figure 24. Differential Input Definition
The amplitude of the differential signal is the difference between
the signals applied to the VIN+ and VIN pins in each differential
pair (that is, VIN+ VIN). VIN+ and VIN should be simultaneously
driven by two signals each of amplitude VREF (or 2 × VREF,
depending on the range chosen) that are 180° out of phase. The
amplitude of the differential signal is therefore VREF to +VREF
peak-to-peak (that is, 2 × VREF). This is regardless of the
common mode (CM). The common mode is the average of the
two signals (that is, (VIN+ + VIN)/2) and is therefore the voltage
on which the two inputs are centered. This results in the span of
each input being CM ± VREF/2. This voltage has to be set up
externally and its range varies with the reference value VREF.
As the value of VREF increases, the common-mode range
decreases. When driving the inputs with an amplifier, the
actual common-mode range is determined by the amplifier’s
output voltage swing.
Figure 25 and Figure 26 show how the common-mode range
typically varies with VREF for a 5 V power supply using the 0 V
to VREF range or 2 × VREF range, respectively. The common
mode must be in this range to guarantee the functionality of the
AD7938-6.
When a conversion takes place, the common mode is rejected,
resulting in a virtually noise-free signal of amplitude VREF to
+VREF corresponding to the digital codes of 0 to 4096. If the
2 × VREF range is used, the input signal amplitude extends from
2 VREF to +2 VREF after conversion.
VREF (V)
0
00.5
1.5
1.0
2.0
2.5
3.0
04
75
1-
0
3
CO
M
O
N-
M
O
DE
RAN
G
E
(
V
)
3.5
3.0
2.0
1.5
2.5
1.0
0.5
3
TA = 25°C
Figure 25. Input Common-Mode Range vs. VREF (0 V to VREF Range, VDD = 5 V)
Figure 26. Input Common-Mode Range vs. VREF (2 × VREF Range, VDD = 5 V)
Driving Differential Inputs
Differential operation requires that VIN+ and VIN be
simultaneously driven with two equal signals that are 180° out
of phase. The common mode must be set up externally and has
a range that is determined by VREF, the power supply, and the
particular amplifier used to drive the analog inputs. Differential
modes of operation with either an ac or dc input provide the
best THD performance over a wide frequency range. Since not
all applications have a signal preconditioned for differential
operation, there is often a need to perform single-ended-to-
differential conversion.
Using an Op Amp Pair
An op amp pair can be used to directly couple a differential
signal to one of the analog input pairs of the AD7938-6. The
how a dual op amp can be used to convert a single-ended signal
into a differential signal for both a bipolar and unipolar input
signal, respectively.
The voltage applied to Point A sets up the common-mode
voltage. In both diagrams, it is connected in some way to the
reference, but any value in the common-mode range can be
input here to set up the common mode. A suitable dual op amp
that can be used in this configuration to provide differential
drive to the AD7938-6 is the AD8022.
It is advisable to take care when choosing the op amp; the
selection depends on the required power supply and system
performance objectives. The driver circuits in Figure 27 and
Figure 28 are optimized for dc coupling applications requiring
best distortion performance.
The differential op amp driver circuit in Figure 27 is configured
to convert and level shift a single-ended, ground-referenced
(bipolar) signal to a differential signal centered at the VREF level
of the ADC.
The circuit configuration shown in Figure 28 converts a
unipolar, single-ended signal into a differential signal.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7938BCPZ | IC ADC 12BIT 8CH 1.5MSPS 32LFCSP |
| AD7940BRM | IC ADC 14BIT UNIPOLAR 8-MSOP |
| AD7942BRMZ-RL7 | IC ADC 14BIT 250KSPS 10-MSOP |
| AD7944BCPZ | IC ADC 14BIT 2.5MSPS 20LFCSP |
| AD7946BCPZRL7 | IC ADC 14BIT 500KSPS 10-LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7938BCPZ-6REEL7 | 功能描述:IC ADC 12BIT 8CH 625KSPS 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7938BCPZ-REEL7 | 功能描述:IC ADC 12BIT 8CH 1.5MSPS 32LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7938BSU | 制造商:Analog Devices 功能描述: |
| AD7938BSU-6 | 制造商:Analog Devices 功能描述:ADC Single SAR 625ksps 12-bit Parallel 32-Pin TQFP |
| AD7938BSU-6REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:8-Channel, 625 kSPS, 12-Bit Parallel ADCs with a Sequencer |
发布紧急采购，3分钟左右您将得到回复。