- 您现在的位置：买卖IC网 > PDF目录294844 > AD7942 (Analog Devices, Inc.) 14-Bit, 250 kSPS PulSAR ADC in MSOP/QFN PDF资料下载
参数资料
| 型号： | AD7942 |
| 厂商： | Analog Devices, Inc. |
| 元件分类： | ADC |
| 英文描述： | 14-Bit, 250 kSPS PulSAR ADC in MSOP/QFN |
| 中文描述： | 14位，250 kSPS的PulSAR系列ADC的，采用MSOP / QFN封装 |
| 文件页数： | 11/28页 |
| 文件大小： | 633K |
| 代理商： | AD7942 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Preliminary Technical Data
AD7942
Rev Pr B | Page 19 of 28
CS MODE 3-Wire, No BUSY Indicator
This mode is usually used when a single AD7942 is connected
to an SPI compatible digital host. The connection diagram is
shown in Figure 29 and the corresponding timing is given in
With SDI tied to VIO, a rising edge on CNV initiates a
conversion, selects the CS mode, and forces SDO to high
impedance. Once a conversion is initiated, it will continue to
completion irrespective of the state of CNV. For instance, it
could be useful to bring CNV low to select other SPI devices,
such as analog multiplexers, but CNV must be returned high
before the minimum conversion time and held high until the
maximum conversion time to avoid the generation of the BUSY
signal indicator. When the conversion is complete, the AD7942
enters the acquisition phase and powers down. When CNV goes
low, the MSB is output onto SDO. The remaining data bits are
then clocked by subsequent SCK falling edges. The data is valid
on both SCK edges. Although the rising edge can be used to
capture the data, a digital host also using the SCK falling edge
will allow a faster reading rate provided it has an acceptable
hold time. After the 14th SCK falling edge or when CNV goes
high, whichever is earlier, SDO returns to high impedance.
CNV
SCK
SDO
SDI
DATA IN
CLK
CONVERT
VIO
DIGITAL HOST
AD7942
Figure 29. CS Mode 3-Wire, No BUSY Indicator
Connection Diagram (SDI High)
04656-P
rC-008
SDO
D13
D12
D11
D1
D0
tDIS
SCK
1
2
3
12
13
14
tSCK
tSCKL
tSCKH
tHSDO
tDSDO
CNV
CONVERSION
ACQUISITION
tCONV
tCYC
ACQUISITION
SDI = 1
tCNVH
tACQ
tEN
Figure 30. CS Mode 3-Wire, No BUSY Indicator Serial Interface Timing (SDI High)
相关PDF资料 |
PDF描述 |
|---|---|
| AD7943BN | +3.3 V/+5 V Multiplying 12-Bit DACs |
| AD7943BR | +3.3 V/+5 V Multiplying 12-Bit DACs |
| AD7943BRS | +3.3 V/+5 V Multiplying 12-Bit DACs |
| AD7945BN | +3.3 V/+5 V Multiplying 12-Bit DACs |
| AD7945BR | +3.3 V/+5 V Multiplying 12-Bit DACs |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD79421 | 制造商:AD 制造商全称:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN) |
| AD7942BCPRL7 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 250 kSPS PulSAR ADC in MSOP/QFN |
| AD7942BCPWP | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 250 kSPS PulSAR ADC in MSOP/QFN |
| AD7942BCPZRL | 功能描述:IC ADC 14BIT SAR 250KSPS 10LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7942BCPZRL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 250 kSPS PulSAR, Pseudo Differential ADC in MSOP/QFN |
发布紧急采购，3分钟左右您将得到回复。