- 您现在的位置：买卖IC网 > PDF目录10566 > AD7942BCPZRL7 (Analog Devices Inc)IC ADC 14BIT 250KSPS 10-LFCSP PDF资料下载
参数资料
| 型号： | AD7942BCPZRL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 250KSPS 10-LFCSP |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| 位数： | 14 |
| 采样率（每秒）： | 250k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 1.25mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘，CSP |
| 供应商设备封装： | 10-LFCSP-WD（3x3） |
| 包装： | 标准包装 |
| 输入数目和类型： | 1 个伪差分，单极 |
| 配用： | EVAL-AD7942CB-ND - BOARD EVALUATION FOR AD7942 |
| 其它名称： | AD7942BCPZRL7DKR |
AD7942
Rev. B | Page 18 of
24
CS Mode 3-Wire with Busy Indicator
This mode is most often used when a single AD7942 is
connected to an SPI-compatible digital host with an interrupt
input. The connection diagram is shown in Figure 32 and the
corresponding timing diagram is shown in Figure 33.
With SDI tied to VIO, a rising edge on CNV initiates a conver-
sion, selects the CS mode, and forces SDO to high impedance.
SDO is maintained in high impedance until the completion of
the conversion irrespective of the state of CNV. Prior to the
minimum conversion time, CNV can be used to select other
SPI devices, such as analog multiplexers. However, CNV must
be returned low before the minimum conversion time and held
low until the maximum conversion time to guarantee the
generation of the busy signal indicator. When the conversion
is complete, SDO goes from high impedance to low impedance.
With a pull-up on the SDO line, this transition can be used as
an interrupt signal to initiate the data reading controlled by the
digital host. The AD7942 then enters the acquisition phase and
powers down. The data bits are then clocked out, MSB first, by
subsequent SCK falling edges. The data is valid on both SCK
edges. Although the rising edge can be used to capture the data,
a digital host also using the SCK falling edge allows a faster
reading rate provided it has an acceptable hold time. After
the optional 15th SCK falling edge or when CNV goes high,
whichever is earlier, SDO returns to high impedance.
CNV
SCK
SDO
SDI
DATA IN
IRQ
CLK
CONVERT
VIO
DIGITAL HOST
AD7942
04
65
7-
0
32
47k
Figure 32. CS Mode 3-Wire with Busy Indicator
Connection Diagram (SDI High)
SDO
D13
D12
D1
D0
tDIS
SCK
12
3
13
14
15
tSCK
tSCKL
tSCKH
tHSDO
tDSDO
CNV
CONVERSION
ACQUISITION
tCONV
tCYC
tCNVH
tACQ
ACQUISITION
SDI = 1
04
65
7-
0
3
Figure 33. CS Mode 3-Wire with Busy Indicator, Serial Interface Timing (SDI High)
相关PDF资料 |
PDF描述 |
|---|---|
| VE-251-IW-F4 | CONVERTER MOD DC/DC 12V 100W |
| VI-25X-MX | CONVERTER MOD DC/DC 5.2V 75W |
| VE-251-IW-F2 | CONVERTER MOD DC/DC 12V 100W |
| VE-251-IW-F1 | CONVERTER MOD DC/DC 12V 100W |
| MAX11617EEE+ | IC ADC SERIAL 12BIT 12CH 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7942BCPZRL71 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 250 kSPS PulSAR, Pseudo Differential ADC in MSOP/QFN |
| AD7942BRM | 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 14-bit Serial 10-Pin MSOP Tube 制造商:Analog Devices 功能描述:IC 14-BIT ADC |
| AD7942BRMRL7 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 250 kSPS PulSAR ADC in MSOP/QFN |
| AD7942BRM-RL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 14-bit Serial 10-Pin MSOP T/R |
| AD7942BRMZ | 功能描述:IC ADC 14BIT 250KSPS 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
发布紧急采购，3分钟左右您将得到回复。