- 您现在的位置：买卖IC网 > PDF目录6054 > AD8139ACPZ-REEL7 (Analog Devices Inc)IC AMP DIFF R-R LN LDIST 8LFCSP PDF资料下载
参数资料
| 型号： | AD8139ACPZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/25页 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF R-R LN LDIST 8LFCSP |
| 标准包装： | 1 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 输出类型： | 差分，满摆幅 |
| 转换速率： | 800 V/µs |
| -3db带宽： | 410MHz |
| 电流 - 输入偏压： | 2.25µA |
| 电压 - 输入偏移： | 150µV |
| 电流 - 电源： | 24.5mA |
| 电流 - 输出 / 通道： | 100mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 12 V，±2.25 V ~ 6 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-VFDFN 裸露焊盘，CSP |
| 供应商设备封装： | 8-LFCSP-VD（3x3） |
| 包装： | 标准包装 |
| 产品目录页面： | 770 (CN2011-ZH PDF) |
| 其它名称： | AD8139ACPZ-REEL7DKR |
AD8139
Rev. B | Page 18 of 24
THEORY OF OPERATION
The AD8139 is a high speed, low noise differential amplifier
fabricated on the Analog Devices second-generation eXtra Fast
Complementary Bipolar (XFCB) process. It is designed to
provide two closely balanced differential outputs in response to
either differential or single-ended input signals. Differential
gain is set by external resistors, similar to traditional voltage-
feedback operational amplifiers. The common-mode level of
the output voltage is set by a voltage at the VOCM pin and is
independent of the input common-mode voltage. The AD8139
has an H-bridge input stage for high slew rate, low noise, and
low distortion operation and rail-to-rail output stages that
provide maximum dynamic output range. This set of features
allows for convenient single-ended-to-differential conversion, a
common need to take advantage of modern high resolution
ADCs with differential inputs.
TYPICAL CONNECTION AND DEFINITION OF
TERMS
Figure 59 shows a typical connection for the AD8139, using
matched external RF/RG networks. The differential input
terminals of the AD8139, VAP and VAN, are used as summing
junctions. An external reference voltage applied to the VOCM
terminal sets the output common-mode voltage. The two
output terminals, VOP and VON, move in opposite directions in a
balanced fashion in response to an input signal.
+
–
VAP
VAN
VON
VOP
–
+
VO, dm
RL, dm
AD8139
CF
RF
RG
CF
RF
VIP
VOCM
VIN
04
67
9-
0
50
Figure 59. Typical Connection
The differential output voltage is defined as
VO, dm = VOP VON
(1)
Common-mode voltage is the average of two voltages. The
output common-mode voltage is defined as
2
ON
OP
cm
O,
V
+
=
(2)
Output Balance
Output balance is a measure of how well VOP and VON are
matched in amplitude and how precisely they are 180° out of
phase with each other. It is the internal common-mode feedback
loop that forces the signal component of the output common-mode
towards zero, resulting in the near perfectly balanced differential
outputs of identical amplitude and exactly 180° out of phase. The
output balance performance does not require tightly matched
external components, nor does it require that the feedback factors
of each loop be equal to each other. Low frequency output balance
is limited ultimately by the mismatch of an on-chip voltage divider,
which is trimmed for optimum performance.
Output balance is measured by placing a well-matched resistor
divider across the differential voltage outputs and comparing
the signal at the midpoint of the divider with the magnitude of
the differential output. By this definition, output balance is
equal to the magnitude of the change in output common-mode
voltage divided by the magnitude of the change in output
differential-mode voltage:
dm
O,
cm
O,
V
Balance
Output
Δ
=
(3)
The block diagram of the AD8139 in Figure 60 shows the
external differential feedback loop (RF/RG networks and the
differential input transconductance amplifier, GDIFF) and the
internal common-mode feedback loop (voltage divider across
VOP and VON and the common-mode input transconductance
amplifier, GCM). The differential negative feedback drives the
voltages at the summing junctions VAN and VAP to be essentially
equal to each other.
VAN = VAP
(4)
The common-mode feedback loop drives the output common-
mode voltage, sampled at the midpoint of the two 500 Ω resistors,
to equal the voltage set at the VOCM terminal. This ensures that
2
dm
O,
OCM
OP
V
+
=
(5)
and
2
dm
O,
OCM
ON
V
=
(6)
VOP
VOCM
GO
GDIFF
GO
GCM
10pF
500
VON
MIDSUPPLY
+
VAN
VIN
VIP
VAP
RG
RF
04
67
9-
0
51
Figure 60. Block Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| D3440-5002-AR | CONN HDR 30POS R/A NO LATCH 10AU |
| SMCJ15A | TVS UNIDIRECT 1500W 15V SMC |
| AD627BRZ-R7 | IC AMP INST R-R 80MHZ DL 8SOIC |
| N3408-6202RB | CONN HEADER 16PS STR SHORT LATCH |
| 951240-8622-AR | CONN HEADER 40POS 2MM VERT T/H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8139AR | 制造商:Analog Devices 功能描述: |
| AD8139ARD | 功能描述:IC AMP DIFF R-R LN LDIST 8SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:Excalibur™ 放大器类型:J-FET 电路数:1 输出类型:- 转换速率:45 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:20pA 电压 - 输入偏移:490µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
| AD8139ARD-EBZ | 功能描述:BOARD EVAL FOR AD8139ARD RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| AD8139ARD-REEL | 功能描述:IC AMP DIFF R-R LN LDIST 8SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:J-FET 电路数:2 输出类型:- 转换速率:3.5 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:30pA 电压 - 输入偏移:2000µV 电流 - 电源:200µA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 |
| AD8139ARD-REEL7 | 制造商:Analog Devices 功能描述:SP Amp DIFF AMP Single R-R O/P 制造商:Analog Devices 功能描述:SP Amp DIFF AMP Single R-R O/P ±6V/12V 8-Pin SOIC N EP T/R |
发布紧急采购，3分钟左右您将得到回复。