- 您现在的位置：买卖IC网 > PDF目录68990 > AD8339ACPZ (ANALOG DEVICES INC) 0 MHz - 50 MHz RF/MICROWAVE I/Q DEMODULATOR PDF资料下载
参数资料
| 型号： | AD8339ACPZ |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 调制器/解调器 |
| 英文描述： | 0 MHz - 50 MHz RF/MICROWAVE I/Q DEMODULATOR |
| 封装： | 6 X 6 MM, ROHS COMPLIANT, MO-220-VJJD-2, LFCSP-40 |
| 文件页数： | 19/36页 |
| 文件大小： | 2970K |
| 代理商： | AD8339ACPZ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
AD8339
Rev. A | Page 26 of
36
CONNECTIONS TO THE BOARD
Table 5 is a list of equipment required to activate the board with
suggested test equipment, and Figure 61 shows a typical setup.
A green LED glows (signifying that the 5 V power through the
USB is present) when the computer is connected via the USB.
However, the LED does not signify that the program is running.
Selecting the frequency of the generators is quite simple. As an
example, select an RF frequency of interest, for example, 5 MHz.
Then select the 4LO frequency, which is four times the RF
frequency, in this example, 20 MHz. The output frequency is
0 Hz. Note that the AD8021 outputs are at either a positive or
negative dc voltage under this condition of perfect RF and 4LO
frequency lock; it is more likely that the signal is slowly varying
if the lock is not perfect.
To detect an output, advance or retard the RF frequency by the
desired baseband frequency. A baseband frequency of 10 kHz at
the output results from an RF frequency of 5.01 MHz or 4.99 MHz.
Table 5. Recommended Equipment List
Description
Suggested Equipment
PC with Windows XP
Any recent laptop
Signal Generators (2) with
Synchronizing Connectors
Rohde & Schwarz SMT03 or
equivalent
4-Channel Oscilloscope
Tektronix DPO7104 or equivalent
Power Supplies
Agilent E3631A or equivalent
Scope Probes (4)
Tektronix P6104 or equivalent
TEST CONFIGURATIONS
The three test configuration options for the AD8339-EVALZ
are common input, independent input, and AD9271 drive.
Common Input Signal Drive
Figure 59 is a block diagram showing the simplest way to use
the evaluation board, with a common signal applied to all four
AD8339 inputs in parallel. Boards are configured this way as
shipped. The inputs of each of the channels are connected in
common by means of jumpers, as shown in Table 6, although
they can just as easily be connected to any of the AD8334 LNA
outputs. As shown in Figure 64, two pairs of summing amplifiers
provide the I and Q outputs so that Channel 1 and Channel 2
can be observed independently of Channel 3 and Channel 4.
Using a common input signal source as shown in Figure 61, the
same input is applied to all four channels of the AD8339. To
observe an output at the I or Q connectors, simply enable the
appropriate channel or channels using the menu shown in
Figure 62. For example, if only Channel 1 is enabled and the
phases are set to 0°, a waveform is seen at the I1 + I2 and Q1 +
Q2 outputs. If Channel 2 is enabled with the phase also set to 0°,
the amplitude of the waveforms doubles. If the Channel 1 phase
is 0° and the Channel 2 phase is set to 180°, the output becomes
zero, because the phases of the two channels cancel each other out.
When using the common input drive mode, it is important that
only the top two positions of P4A and P4B be used to avoid
shorting the LNA outputs together.
Independent Channel Drive
Independent input mode means that each channel is driven by
an LNA. The LNA inputs of the AD8334 can be driven by up to
four independent signal generators or from a single generator. If
the user chooses this mode, it is important not to connect the
LNA inputs in parallel because of the active matching feature.
Any standard splitter can be used.
AD9271 Input Drive
Connectors P3A, P3B, P4A, and P4B are configured to route
input signals from the AD8334 LNA outputs or from an AD9271
evaluation board. The AD9271 is an octal ultrasound front end
with a 12-bit ADC for each channel. When using an AD9271 as
an input drive, consult the AD9271 data sheet for setup details.
The AD9271 evaluation board is attached to the AD8339 by
inserting the three plastic standoffs into the three guide holes in
the AD8339-EVALZ board; all the jumpers in P3 and P4 are
removed. The bottom connectors of the AD9271 board engage
P3 and P4 and route the LNA outputs of the AD9271 to the
AD8339. Figure 60 is a photograph of the two boards attached.
Table 6. P3, P4 Input Jumper Configuration
Common Input
Independent Input
P4A-1 to P4B-1, top two
positions (2)
P3A-1 to P3B-1, P4A-1 to P4B-1
RF12N, RF12P, RF23N, RF23P,
RF34N, RF34P
P3A-1 to P3B-1, P4A-1 to P4B-1,
all positions (8)
相关PDF资料 |
PDF描述 |
|---|---|
| ADL5374ACPZ-WP | 3000 MHz - 4000 MHz RF/MICROWAVE QUADRAPHASE MODULATOR |
| ADL5375-05ACPZ-R7 | 400 MHz - 6000 MHz RF/MICROWAVE I/Q MODULATOR |
| AH212-S8G | 1800 MHz - 2400 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| AK1222 | 100 MHz - 900 MHz RF/MICROWAVE SINGLE BALANCED MIXER |
| ALM-40220-BLKG | 2010 MHz - 2025 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 0.45 dB INSERTION LOSS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8339ACPZ-R7 | 功能描述:IC DEMODULATOR I/Q QUAD 40LFCSP RoHS:是 类别:RF/IF 和 RFID >> RF 解调器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:解调器 LO 频率:- RF 频率:70MHz ~ 300MHz P1dB:-9dBm 增益:- 噪音数据:6.36dB 电流 - 电源:41.5mA 电源电压:2.7 V 封装/外壳:28-WFQFN 裸露焊盘 供应商设备封装:28-TQFN-EP（5x5） 包装:带卷 (TR) |
| AD8339ACPZ-RL | 功能描述:IC DEMODULATOR I/Q QUAD 40LFCSP RoHS:是 类别:RF/IF 和 RFID >> RF 解调器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:解调器 LO 频率:- RF 频率:70MHz ~ 300MHz P1dB:-9dBm 增益:- 噪音数据:6.36dB 电流 - 电源:41.5mA 电源电压:2.7 V 封装/外壳:28-WFQFN 裸露焊盘 供应商设备封装:28-TQFN-EP（5x5） 包装:带卷 (TR) |
| AD8339-EVALZ | 功能描述:BOARD EVAL AD8339 I/Q DEMOD RoHS:是 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
| AD834 | 制造商:AD 制造商全称:Analog Devices 功能描述:500 MHz Four-Quadrant Multiplier |
| AD834_12 | 制造商:AD 制造商全称:Analog Devices 功能描述:500 MHz Four-Quadrant Multiplier |
发布紧急采购，3分钟左右您将得到回复。